The 100-mm diameter shaft is composed of brass (G=34.5 GPa) and steel (G=82.7 GPa) sections rigidly connected. Determine the maximum allowable torque, applied as shown, if the maximum shearing stresses in the brass and the steel are not to exceed 51.7 MPa and 68.90 MPa, respectively, and the distance AC, through which the end of the 250-mm pointer AB moves, is not to exceed 15 mm. Brass 100-mm diam. Steel 1.80 m 1.20 m 0.3 m C B 250 mm

The 100-mm diameter shaft is composed of brass (G=34.5 GPa) and steel (G=82.7 GPa) sections rigidly connected. Determine the maximum allowable torque, applied as shown, if the maximum shearing stresses in the brass and the steel are not to exceed 51.7 MPa and 68.90 MPa, respectively, and the distance AC, through which the end of the 250-mm pointer AB moves, is not to exceed 15 mm. Brass 100-mm diam. Steel 1.80 m 1.20 m 0.3 m C B 250 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Similar questions

Determine the required length of cord AC shown so that the 8-kglamp can be suspended in the position shown. The undeformed lengthof spring AB is l'AB = 0.4 m, and the spring has a stiffness of kAB = 300 N/m.
The solid 28 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 550 N, Q = 1150 N, LAB = 350 mm, LBC = 600 mm, LCD = 600 mm.
The solid 21 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine:(a) the shaft deflection at pulley A.(b) the shaft deflection at pulley C.Assume P = 850 N, Q = 950 N, LAB = 650 mm, LBC = 900 mm, LCD = 900 mm.
For the frame loaded as shown, draw the complete and correct FBDs of thefollowing: whole frame, member BE, member HK, pulley D, pulley J, member CDEHJwithout the pulleys, and pin B. If block G weighs 133 N, determine all the forcesacting on member CDEHJ (i.e. Cx, Cy, Dx, Dy, FBE, FHK, Jx and Jy). Also, calculate thehorizontal (ABCBx) and vertical (ABCBy) components of the reactions betweenmember ABC and pin B.
The rigid pipe is supported by a pin at A and an A-36 guy wire BD (E = 29 000 ksi). If the end C is displaced 0.75 in. downward when P isapplied. a.) Determine the elongation of the guy wire in inches when load P is applied.b.) What is the required diameter of the guy wire in inches to support the load P = 42 kips?
The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. For the loading shown, determine: (a) the shaft deflection at pulley B. (b) the shaft deflection at pulley C. Assume P = 810 N, Q = 480 N, LAB = 260 mm, LBC = 400 mm
Steel Design Two channels having the given properties shown is placed at a distance of 300 mm to back and is properly connected by a pair of lacings as shown. Properties of one channel A = 5595 mm2 d = 305 mm x = 17mm Ix = 67.3 x 106 mm4 Iy = 2.12 x 106 mm4 rx = 19.3 mm Assume K = 1.0 Determine the safe axial load in kN, that the column section could carry. Unsupported height of column is 6m.
BAL=8 mt = 13 mm-150 mm113 mmFor the steel column with both ends fixed against rotation having a tubularcross-section, determine the allowable load Pall against buckling. E=200 GPa andOy=250 MPa.
The rigid pipe is supported by a pin at A and an A-36 guy wire BD. If the wire has a diameter of 6.5 mm, determine the load P if the end C is displaced 1.675 mm downward.
200-Ib block is suspended from an inextensible cable which is wrapped around a drum of 1.3-ft radius rigidly attached to a flywheel. The drum and flywheel have a combined centroidal moment of Inertia lG = 10 Ib-ft-s^2 At the instant shown, the velocity of the block is 5 ft/s directed downward. Knowing that the bearing at A is poorly lubricated and that the bearing friction is equivalent to a couple M of magnitude 60 Ib-ft, determine the velocity of the block after it has moved 4.2 ft downward (in ft/s).
please help! upvote will be given. NO LONG EXPLANATION NEEDED STRENGTH OF MATERIALS The compound shaft carries the two torques shown. The shear moduli are 28 GPa for aluminum, 83 GPa for steel, and 35 Gpa for bronze. If T = 1179.9 Nm, U = 4330 Nm, x = 3.03 m, y = 2.25 m, z = 1.34 m, d = 94 mm, and e = 76 mm, find the angle of rotation of the free end of the shaft. Round off the final answer to two decimal places.
Determine the diameter of a 2m long solid shaft for a jeep having power of 80HP, if it is to be made with strength of 100MPa and modulus of rigidity as 9 * 104 N/mm2 the twist in the shaft should not exceed 1 degree. Use FOS of 2 for design in shear.