The 16 x 22 x 25-mm rubber blocks shown in the figure are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 300 N causes the upper frame to be deflected downward by d = 9.5 mm. Determine the average shear strain in the rubber blocks. 0.580 rad 0.444 rad O 0.401 rad O 0.322 rad O 0.536 rad Double U anti-vibration shear mount 16 Shear deformation of blocks 25 Rubber block dimensions KBA

The 16 x 22 x 25-mm rubber blocks shown in the figure are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 300 N causes the upper frame to be deflected downward by d = 9.5 mm. Determine the average shear strain in the rubber blocks. 0.580 rad 0.444 rad O 0.401 rad O 0.322 rad O 0.536 rad Double U anti-vibration shear mount 16 Shear deformation of blocks 25 Rubber block dimensions KBA

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.17P: A shock mount constructed as shown iu the figure is used to support a delicate instrument. The mount...

See similar textbooks

Similar questions

Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
The normal strain in the 45n direction on the surface of a circular tube (sec figure) is 880 × 10 when the torque T = 750 lb-in. The tube is made of copper alloy with G = 6.2 × 106 psi and y = 0.35. If the outside diameter d2of the tube is 0.8 in., what is the inside diameter dt? If the allowable normal stress in the tube is 14 ksi, what is the maximum permissible inside diameter d?
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
A block B is pushed against three springs by a force P (see figure). The middle spring has a stillness K1and the outer springs each have stiffness k^. Initially, the springs are unstressed, and the middle spring is longer than the outer springs (the difference in length is denoted s). (a) Draw a force-displacement diagram with the force P as ordinate and the displacement x of the block as abscissa. (b) From the diagram, determine the strain energy U1 of the springs when x = 2s. (c) Explain why the strain energy E, is not equal to P
A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
A rubber ball (sec figure) is inflated to a pressure of 65 kPa. At that pressure, the diameter of the ball is 240 mm and the wall thickness is 1.25 mm. The rubber has a modulus of elasticity E = 3,7 MPa and Poisson's ratio v = 0.48. (a) Determine the maximum stress and strain in the ball, (b) If the strain must be limited to 0.425, Find the minimum required wall thickness of the ball.
A circular aluminum tube of length L = 600 mm is loaded in compression by forces P (see figure). The outside and inside diameters are d2= 75 mm and d1= 63 mm, respectively. A strain gage is placed on the outside of the lube to measure normal strains in the longitudinal direction. Assume that E = 73 GPa and Poissons ratio is v = 0.33. (a) IF the compressive stress in the tube is 57 MPa, what is the load P? (b) If the measured strain is e = 78 J X 10-6, what is the shortening
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.