The 16 x 22 x 25-mm rubber blocks shown in the figure are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 290 N causes the upper frame to be deflected downward by d = 8.5 mm. Determine the average shear strain in the rubber blocks. Double U anti-vibration shear mount 25

The 16 x 22 x 25-mm rubber blocks shown in the figure are used in a double U shear mount to isolate the vibration of a machine from its supports. An applied load of P = 290 N causes the upper frame to be deflected downward by d = 8.5 mm. Determine the average shear strain in the rubber blocks. Double U anti-vibration shear mount 25

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.19P: During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as...

See similar textbooks

Similar questions

Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
Solve the preceding problem if the plate is made of aluminum with E = 72 GPa and Poisson’s ratio v = 0.33. The plate is loaded in biaxial stress with normal stress sx= 79 MPa, angle Ø = 18°, and the strain measured by the gage is e = 925 × 10-6.
An clement of material in plane strain (see figure) is subjected to strains ex= 480 × 10-6, Ey= 70 × l0-6, and yxy= 420 × l0-6. Determine the following quantities: (a) the strains for an element oriented at an angle 0 = 75°, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements.
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
Solve the preceding problem if the thickness of the steel plate is. t = 12 mm. the gage readings are x = 530 × 10-6 (elongation) and y = -210 -× l0-6 (shortening), the modulus is E = 200 GPa, and Poisson’s ratio is v = 0.30.
A block B is pushed against three springs by a force P (see figure). The middle spring has a stillness K1and the outer springs each have stiffness k^. Initially, the springs are unstressed, and the middle spring is longer than the outer springs (the difference in length is denoted s). (a) Draw a force-displacement diagram with the force P as ordinate and the displacement x of the block as abscissa. (b) From the diagram, determine the strain energy U1 of the springs when x = 2s. (c) Explain why the strain energy E, is not equal to P
1 A rectangular steel plate with thickness t = 5/8 in. is subjected to uniform normal stresses a and ., as shown in the figure. Strain gages A and B. oriented in the x and v directions. respectively, arc attached to the plate. The gage readings give normal strains = 0.00065 (elongation) and £. = 0.00040 (elongation). Knowing that E = 30 X 106 psi and v = 0.3, determine the stresses c7 and a, and the change .11 in the thickness of the plate.
A spherical balloon with an outer diameter of 500 mm and thickness 0.3 mm is filled with a gas. Calculate maximum permissible pressure in the balloon if the allowable normal strain at the outer surface of the balloon is O.h Assume E = 4 MPa and v = 0,45.
Two concentric heavy steel springs support a load of 9100 N as shown in the figure. The outer spring is made from a 30-mm diameter wire on a mean diameter of 220 mm and has 22 turns. The inner spring consists of 30 turns made from 20-mm diameter wire on a mean diameter of 160 mm. Using G = 83 GPa, calculate the shearing stress developed in the two springs. τinner = ? MPa τouter = ? MPa (Provide detailed solution)