Correct and complete solution please don't copy The 3-in. I beam shown in the figure below has cross-sectional properties of A = 1.64 in?.ln = 2 in.", and I2 =0.46 in.“. It is made of steel having Sy = 42 ksi. Find the safe axial compressive load(in lb) based on a safety factor of 4 for pinned ends and unsupported length of 27.3 in.2Answer:

Given data A=1.64 in2 I11= 2 in 4 I22=0.46 in4 Sy= 42Ksi F.O.S =4 Unsupported length= 27.3 in

The 3-in. I beam shown in the figure below has cross-scctional properties of A - 1.64 in.". In= 2 in.", and I2 -0.46 in.". It is made of steel having S, 42 ksi. Find the safe axial compressive load (in lb) based on a safety factor of 4 for pinned ends and unsupported length of 27.3 in. Answer:

The 3-in. I beam shown in the figure below has cross-scctional properties of A - 1.64 in.". In= 2 in.", and I2 -0.46 in.". It is made of steel having S, 42 ksi. Find the safe axial compressive load (in lb) based on a safety factor of 4 for pinned ends and unsupported length of 27.3 in. Answer:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A steel rod of length L and uniform cross sectional area A is secured between two walls, as shown. U...

Q: Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load ...

A: The given figure is shown below:

Q: Design a concrete mix for the following conditions and constraints using absolute volume method. Des...

A: beams and reinforced walls different conditions for fine aggregate and coarse aggregate is provided....

Q: r flows in a trapezoidal channel of 2 m width and side slope at 1:1. At upstream depth of 2 m, the :...

Q: plain this principlein relation to restress concrete design.

A: The basic principle related to design of prestress concrete is that

Q: 1. A car starts from rest and accelerates uniformly over a time of 5.21 seconds for a total distance...

A: Given data : Initial velocity (U)=0 m/s Time (t)=5.21 s Distance covered (S)=110 m To find : Accel...

Q: 49. What is the problem of rehabilitation? A. O Unique B. O Submerged C. O Lined D. O Layered

A: Rehabilitation means modifying the existing structure to increase it's functionalities and level of ...

Q: 10

A: Given:- a1=0.2ppm/ton a2=0.2ppm/ton background pollution is 40 ppm, pollution from source 1 is 100 t...

Q: P2 = 20 kN P1 = 30 kN Wi = 12.5 kN/m 7.5 kN/m WL = 10.5 kN/m WD 4.5 kN/m WD %3| D A 2.5 m 3 m 10 m 8...

Q: Determine the equivalent state of stress on an element at the same point oriented 0 = 40° clockwise ...

Q: TIME OF SETTING OF HYDRAULIC CEMENT BY VICAT NEEDLE make up solution / give example with solution ...

A: Initial setting time: The time elapsed between the moments when water is added to the cement to the...

Q: if the traverse will be adjusted using compass rule, determine the adjusted distance of course BC

Q: An incompressible air is flowing at a velocity of 60 mph through a duct 4 sq. ft. in cross-section. ...

Q: PROBLEM 2: A bolted connection shown is connected by 20 mm diameter bolts with an edge distance of 5...

A: Given. Diameter of bolt ,d=20 mm Thickness of plate t=12 mm fu=415 MPa edge distance e= 50 mm fub=40...

Q: determined that the elevation of point Q

Q: 1000 If 100 570 650 A + 325 All dimensions are in mm The cross-section at mid-span of a beam at the ...

Q: [14] Electrolysis process is based on : * thermal effect of current O chemical effect of current lum...

A: ELECTROLYSIS : Electrolysis is the famous technic in which we use the direct electric current of ...

Q: L L. RAY, MA, RCY, RFy, MF, VB, VCL, VCR, VD, VE, Mc, VB, VD, VE, 6c BO

Q: An angle was measured by ten different observers. The mean of each set and its probable error is sho...

A: To Determine Most probable value of the angle, MPV

Q: Which defect occurs if a paint is applied excessively thick?

A: What defect occur if excess paint is applied

Q: Determine value of Re

A: Given data : Point load FB=10 kips Point load FC=20 kips Point load FD=15 kips To find : Reaction ...

Q: A prestressed concrete rectangular beam of size 500mm by 750mm has a simple span of 9.0m. The beam i...

Q: Prob. 2.2-11. A rigid, weightless beam BD supports a load P and is, in turn, supported by two hanger...

Q: Draw shear and moment diagram for the following frame: by Method Coherent deformations. (q1=4,0K , q...

Q: ce from the PC to the Pl is 376m and the tangent distance from the PC to t common tangent and the ta...

A: According to given data The long chord of a compound curve is parallel with the 200 m common tangen...

Q: Water flows steadily through a nozzle at 60 kg/s. the diameters are D1 = 220 mm and D2 = 80 mm. Comp...

Q: Example 6.5. The lowest level of an impounding reservoir, situated in hills and being used as a sour...

Q: How are we gonna design the height of the earth-fill dam from the ground? For example, We are requir...

A: The dam's height is the vertical distance from the natural streambed at the dam's downstream toe to ...

Q: 2. Construct a cash flow diagram that represents the amount of money that will be accumulated in 15 ...

Q: The beam shown is supported by a pin support at A and a roller support at E. If E=20.5GPA and I=6.75...

Q: 3. Defermine how many pieces of wood needed for window frame that requires 30 pieces having a 2 x 6 ...

A: Windows are fixed into the wall openings in the buildings for entry of daylight and air circulation....

Q: The double T-beam is fabricated by welding three plates together as shown, determine the shear flow ...

A: Step 1: Y = 46 x 1.34x 1.34/2 +2 x 0.94x(22-1.34)x(1.34+10.33)/100.4 = 4.926 cm Computing, I = 1631 ...

Q: 41. Which of the below is a pigment imparting brown colour? A. O Raw Sienna B. O Soot C. O Burnt Sie...

A: To Determine Which of the given options is a pigment imparting brown colour.

Q: Replace the three forces shown by an equivalent force-couple system at point A. If the forces are re...

Q: Calculate the interior angels of the following travers: Line Fore bearing (F.B) АВ 130° 14' ВС 50° 2...

A: Please see the attached solution, thanks

Q: A 450mm x 650mm concrete beam is prestressed with a final prestressing force of 900kN at an eccentri...

Q: BEARING N 32° 14' W N 53° 42' E S 67° 28' E S 48° 57' W COURSE DISTANCE АВ 115.28 ВС 165.83 CD 206.9...

Q: The deflection curve for a simple beam AB (see figure) is given by the following equation: A. De...

A: ##using deflection curve equation CALCULATIONS of Loading, Reaction, And BM ##

Q: Situation - The beam BC shown is supported by a quarter- -circular are AC having a radius of 5- m. T...

A: To Determine The minimum diameter (mm) of the pin at B. The minimum diameter (mm) of the pin at C.

Q: incompressible air is flowing at a velocity of 60 mph through a duct 4 sq. ft. in cross-section. The...

Q: Unfactored maximum bending moments at a section of a reinforced concrete beam resulting from a frame...

A: Given unfactored bending moment for reinforced beam Due to Dead load(DL) = 50 KN-m Live load(LL) ...

Q: determine the linear error of the closure.

A: Given Data - To Find - linear error of the closure.

Q: The following principle is taken from Abeles (Ref. 2.32) and applicable not only to prestressing con...

A: Concept- Prestressed concrete- It is a method that uses strong steel ropes, ropes, or rods to create...

Q: ANGLE MEASURED VALUE ANGLE MEASURED VALUE 312 o'24" 4759' 40" 137 10' 29" 57 02' 42" 100 40' 25" 65 ...

Q: Draw the influence line for member BC and interpret the diagram. F H 15 ft E 4 @ 20 ft = 80 ft- %3D

Q: The surface of the concrete was ---- result temporary continuous hardened * The roof should have a -...

Q: [10] In parallel branches, the current will be the same unless all the resistances are the same. Tru...

A: 10. In parallel branches, the current will be the same unless all the resistances are the same. True...

Q: 50 ka 30 kw lm 2 m E Im 7 im B sm C 4m 6m

Q: low of 250 N/h to lubricate a thrust bearing. The steady oil fl xits radially through the narrow cle...

A: According to given data Oil (SG =0.89) enters at section 1 in Fig. P3.20 at a weight flow of 250 ...

Q: 3.6-5 Use load and resistance factor design and select an American Standard Channel shape to resist ...

A: The given values are as follows The factored tensile load=180kipsThe length =15ftThe shear lag faoto...

Question

Correct and complete solution please don't copy

The 3-in. I beam shown in the figure below has cross-sectional properties of A = 1.64 in?.
ln = 2 in.", and I2 =0.46 in.“. It is made of steel having Sy = 42 ksi. Find the safe axial compressive load
(in lb) based on a safety factor of 4 for pinned ends and unsupported length of 27.3 in.
2
Answer:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the beam shown below, given that L = 6 m, and w = 3 kN/m, draw the FBD, shear & momment diagram, and then input the magnitude of the max internal bending moment along the beam: ____ kN m. Calculate your solution to 1 decimal place.
Select the lightest possible W-section for the beam shown in Figure 1. Assume ?? =50 ?, full compression flange lateral support, and exclude beam self-weight.
A cantilever beam AB with a rectangularcross section has a longitudinal hole drilled throughoutits length (see figure). The beam supports a loadP 5 600 N. The cross section is 25 mm wide and50 mm high, and the hole has a diameter of 10 mm. Find the bending stresses at the top of the beam,at the top of the hole, and at the bottom of the beam.
F=11 kN single load, M=22 kN.m moment and w=5 kN/m distributed load act on the beam whose loading condition is given in the figure. The length L is also given as L=5 m. The cross-sectional properties of the beam are; body height yg=218 mm, body thickness xg=18 mm, flange width xf=190 mm, flange height yf=13 mm. Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the B level of the beam. According to this;
For the beam and loads shown: a) Calculate and draw the bending moment and shear force diagrams. B) Calculate the maximum bending stress and maximum shear. The value of the force P1 is 5 kN and that of the distributed load w1 is 4 kN / m The cross section is rectangular with the following measurements
For this Problem, kindly refer to our Textbook, Structural Analysis Fourth Edition By Aslam Kassimali. For the given frame on Problem 5.62 Page 224, calculate the Shear Force in kips at Point B (Member BC) if the given 20kip and 0.5kip/ft loads from the figure are both replaced by 37kips and 0.9kip/ft respectively. Express your answer in 2 decimal places. Include (-) negative sign if the shear force is negative.
The I-section displayed is made up of five boards (four 40x40mm and one 40x380mm). If the allowed stress in bending is 12 MPa and in shear is 0.8 MPa, calculate the load (p in kN/m) that this beam can carry over a span of 4 m, dispersed over its length.
Calculate the force on Member CH in Kips by the method of sections. if the given 30kip load at joint J and 25kip loads at joints B, C, D, E from the figure are replaced by 85kip and 108kip loads respectively. Express your answer in 2 decimal places. Include (-) negative sign if the force is compression.
By DIM & MAM, determine the value of EIẟ at midspan for the beam loaded as shown. Take note that L, a, b, c, d, e are in m, P1 & P2 are in KN, and W is in KN/m.
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
Answer in 3 decimal places please. Thank you. The cantilever beam shown is subjected to a concentrated load of P. The cross-sectional dimensions of the wide-flange shape are also shown, where bf = 7.00 in., d = 14.0 in., tf = 0.475 in., tw = 0.350 in.(a) Compute the value of Q that is associated with point K, which is located yk = 3.5 in. above the centroid of the wide-flange shape.(b) If the allowable shear stress for the wide-flange shape is τallow= 13 ksi, determine the maximum concentrated load P than can be applied to the cantilever beam.Calculate the cross-sectional area of the top flange (1), the bottom flange (2), and the web (3).Answers:A1 = in.2.,A2 = in.2.,A3 = in.2. Determine the location of the y direction centroids of the top flange (1), the bottom flange (2), and the web (3), with respect to the bottom of the cross-section.Answers:y1 = in.,y2 = in.,y3 = in. Determine the centroid location in the y direction for the cross-section…
The frame has loads P₁ = 8.2 kN, P₂ = 8.7 kN, and P3 = 6.1 kN. Assume Joint B is rigid-connected and Joint C is pin- connected. Both Supports A and D are hinges. Determine the magnitude of the shear force at right of Beam BC (at Joint C). Please provide your answer in kN and to two decimal points. Answer: