The 300 kgs truck heading east running a constant velocity of 20ft/s ,after 15 seconds when suddenly bumped to 250 kgs similartruck at restand caused to displaced 10 meters in 5 seconds. The point of bumping contact is 3 meters above the grounds. Determinethe ff: A. Bumping Force in kn B. Friction Force at rear wheels of 250 kg truck in kn CG 2.5 ft 4ft

The 300 kgs truck heading east running a constant velocity of 20ft/s ,after 15 seconds when suddenly bumped to 250 kgs similartruck at restand caused to displaced 10 meters in 5 seconds. The point of bumping contact is 3 meters above the grounds. Determinethe ff: A. Bumping Force in kn B. Friction Force at rear wheels of 250 kg truck in kn CG 2.5 ft 4ft

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter15: Slope Stability

Section: Chapter Questions

Problem 15.28P

See similar textbooks

Similar questions

A block weighing 100Nis held on a 40 ̊incline by a bar attached to a 150N block on a horizontal plane. The bar, which is fastened by smooth pins at each end, is inclined 20 ̊above the horizontal. The angle of friction between each block and its plane is 18 ̊. Fin the horizontal force P applied to the 150N block which will cause to be on the point of moving (a) to the right; (b) to the left.
: Block B has a mass m and is released from rest when it is on top of cart A, which has a mass of 3kg. Determine the tension in cord CD needed to hold the cart from moving while B slides down A. Neglect friction. =30o
If the block is 1000jg, determine the value of force P(N) that is causing the movement of the block usubstatic=0.50 and usubkinetic=0.35. A. 4700N B. 5000N C. 0 D. 4905N
The two blocks (MA = 100 kg, MB = 150 kg) shown are originally at rest. Assuming that the coefficients of friction between the blocks and the inclines are ms = 0.25 and mk = 0.20, determine a. acceleration of block A b. tension in the cord
An unbalanced vertical force of 60lb upward accelerates 1.55ft3 of water. If the water is 3ft deep in a cylindrical tank, which of the following most nearly gives the force acting on the bottom of the tank?
The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 04 between both collars and the rod determine the maximum supporting force available from friction when F = 0 and when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 618.75
Calculate the value of the deflection at point B due to concentrated load P in the form Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
If F 1 = 600 N and = 30°, determine the magnitude of the resultantforce acting on the eyebolt.
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
The super elevation of a railroad track is the number of inches that theoutside rail is raised to prevent side thrust on the wheel flanges of carsrounding the curve at rated speed. Determine the super elevation e for a track having a gauge of 4 ft 8 1/2 in. of 2000-ft radius and a rated speed of 60 mph.What is the flange pressure P on the wheels of a 100,000-Ib car that rounds the curve at 80 mph?
Home Work H.W(l Blocks A.B and C have weights of 50N.25N and 15N respectively. Determine the smallest horizontal force P that will cause impending motion. The coefTicient of static friction between A and B is p=0.3, between B and C is H=0.4. and between block C and the ground is p=0.35.(Ans: P=45N)
If the equivalent single force of the system is zero, determine the magnitude and direction of F1 and its direction if F3=458 N and F2=280 N and β=36°.