The 81-lb force P is applied to the 220-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.42, k = 0.30. P Answer: F= i Hk lb

The 81-lb force P is applied to the 220-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.42, k = 0.30. P Answer: F= i Hk lb

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A minimum force of P = 50 lb is required to hold the cylinder from slipping against the belt and the wall. Determine the weight of the cylinder if the coefficient of friction between the belt and cylinder is μs = 0.3 andslipping does not occur at the wall.
Determine the smallest force P needed to lift the 3000-lb load. The coefficient of static friction between A and C and between B and D is μs = 0.3, and between A and B μ's = 0.4. Neglect the weight of each wedge.
The 40 kg block is placed on a 30° inclined and released from rest. The coefficient of static friction between the block and the inclined plane is 0.30. A) Determine the maximum value of the initial tension T in the spring for which the block will not slip when released. B) Determine the minimum value of the initial tension T in the spring for which the block will not slip when released. C) Determine the friction force on the block if T = 150 N.
Refer figure 1: Determine the deflection (delta) in mm at point B. Use E = 200 GPa and I = 2100 mm^4 What is the vertical support reaction at the hinge as shown in the figure below.
If A = 1 kg, B = 2 kg, C = 801 kg, and the static of coefficient friction is equal to 0.04. Determine the normal force exerted by the horizontal plane to Block B. Find the force F required to start C moving upward. Nb = Blank 1 N F = Blank 2 N
Determine thy vertical displacement (mm) of joint B. Support A is roller and support D is hinge. A=2500 mm2 E=200 GPa
Based on the following figure if the value of F is equal to 2541 N and the angle α is equal to 26.3°. Determine the minimum mass of the block A (in kg) so that it does not slide to the right product of the force F, if it is known that the static coefficient of friction is 0.25 and the dynamic is 0.2.
in figure shown the cylinder has a wieght w and radius r , and the coefficient of static friction is the same at A and B ,Determine the magnitude of the largest couple moment can be applied to the cylinder if it is not rotate.
Questions b and c. The pressure from part a is 0.86832 Mpa
Determine the force P needed to pull the 50-kg roller over the smooth step. Take θ = 30°.
If the beam AD is loaded as shown, determine the horizontal force P which must be applied to the wedge in order to remove it from under the beam. The coefficients of static friction at the wedge’s top and bottom surfaces areμCA = 0.25 and μCB = 0.35, respectively. If P = 0, is the wedge self-locking? Neglect the weight and size of the wedge and the thickness of the beam.
Determine the minimum force P to prevent the 30-kg rod AB from sliding. The contact surface at B is smooth, whereas the coefficient of static friction between the rod and the wall at A is μs = 0.2.