The Achilles tendon force F, is mobilized when the man tries to stand on his toes. As this is done, each of his feet is subjected to a reactive force of N, = 400 N. If the resultant moment produced by forces F, and N, about the ankle joint A is required to be zero, determine the magnitude of F,. F, 5°- 200 mm 65 mm Nf = 400 N 100 mm

The Achilles tendon force F, is mobilized when the man tries to stand on his toes. As this is done, each of his feet is subjected to a reactive force of N, = 400 N. If the resultant moment produced by forces F, and N, about the ankle joint A is required to be zero, determine the magnitude of F,. F, 5°- 200 mm 65 mm Nf = 400 N 100 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.71P: The force F=5i+12j+4k lb is applied to the handle of the door. Determine the orthogonal component of...

See similar textbooks

Similar questions

The convergent system of 4 forces acting on an absolutely rigid body is balanced (ΣFKY = 0). Determine the projection of the fourth force on the Oy axis if F1y = 160.0 kN; F2y = -46.0 kN; F3y = 36.0 kN;.
How much work is done by the force in the spring when the slender rod rotates clockwise about the fixed pin support at O from the vertical position (where AB is horizontal) to the horizontal position? The spring has a stiffness of k = 125 N/m and an unstretched length of 0.15 m. Take d1= 0.29 m and d2= 0.85 m. Choose the correct answer. a) 94.9 Joule b) 99.9 Joule c) -99.9 Joule d) 0 Joule e) -94.9 Joule
Determine whether or not it is stable for that position. R=0.75m h=1.50m
The force system acting on the machine part is equivalent to the single force R=80i + 20jlb acting at O. Determine the force P and the distance b.
The pole is subjected to the force F which has components Fx = 1.6 kN and Fz = 1.35 kN. If β = 72, determine the magnitude of Fy and F
If F=1kN,the magnitude of the vertical reaction force developed at the point B?
The 12ft pole AC (negligible mass) lies in the y-z plane and forms a 30° angle with the z-axis. The pole is held in place at point C by a ball-and-socket joint. Two cables, BD and BE, are fixed to the pole at point B (these represent two separate cables attached at B). A 110 lb force pulls downward at the end of pole AC in the vertical direction (y-direction). If the distance between B and C along the feet, determine the Reactions at C (ball-and-socket joint) The tension in cables BD and BE.
The left and right strings have a mass of 0.01 kg, the middle string has a mass of 0.02 kg. Both theta and beta angles are 40 degrees. Show the calculations used to determine the horizontal and vertical components of the tension forces connected to the center string.
If the tension developed in each of the four wires is not avowed to exceed 560 N , 1. determine the maximum mass of the chandelier that can be supported. 2. Draw a free-body diagram of the ring B. (Draw the vectors starting at the black dot) 3. Draw a free-body diagram of the ring D. (Draw the vectors starting at the black dot)
3. Determine whether the 10 kg block shown is in equilibrium, and find the magnitude and direction of the friction force when P = 40 N and 0 = 20⁰. μ = 0.30 M = 0.25 20°
The ball ( D ) has a mass of ( 15 kg ). If a force of (F = 80 N ) is applied horizontally to the ring at ( A ), determine the largest dimension ( d) so that the force in cable (AC ) is zero.
Since the system is in static equilibrium, find the forces that occur in AB and AC ropes.g = 9.81 m / s2