The actual velocity in the contracted section of a jet of liquid flowing from a 50mm diameter orifice is 9.21 m/s under a head of 4.57 m. what is the value of coefficient of velocity? Ans in 4 decimal places.

The actual velocity in the contracted section of a jet of liquid flowing from a 50mm diameter orifice is 9.21 m/s under a head of 4.57 m. what is the value of coefficient of velocity? Ans in 4 decimal places.

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter15: Computational Engineering Tools Matlab

Section: Chapter Questions

Problem 29P

See similar textbooks

Related questions

Q: Refer to the given figure. Given: a = 36cm, b = 24cm, and c = 29cm Water ← b с Į 40 cm Gate Unknown…

A: use simple method just find force by individual fluid and make net force zero on the gate

Q: Torsion. A 40-mm diameter, 533-mm length shaft is drilled, for a part of its length L₁, to a 20 mm…

A: Given: Length Diameter Shear stress To find: Length Power

Q: 25 A P₁ 45 P2 no to 45 P2 25 P₁ 45 P2 E 6 panels @ 3.0 m = 18.0 m 43 P₂ K 25 P₁ 6.0 m

A: Solution: Here it is a symmetric section and the loadings also symmetrical. Hence it is enough to…

Q: A machine frame shown in the figure below is subjected to a horizontal force of 600 N parallel to…

A: Given data: diameter = 30mm F=600 N

Q: Pinned > A -15 ft- 2 k/ft V Roller пів * -sff- moupported joint EI = Constant E = 29,000 ksi .4 I =…

A: Given A beam with loadings Required Maximum deflection in the beam using conjugate beam method

Q: shear stress in the wall?

A: Given data, Inner radius of a cylindrical tank is, r=12 mwall thickness,t= 75 mmGauge…

Q: Problem 3. Determine the following unknowns on the beam shown below using Conjugate-Beam Method.…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: AURS L1 RA= W1 Consider the following values in the given beam above: L1 = 6 m L2= 2m L3 = 4 m L4 =…

Q: ASSIGNMENT 2 Obtain the stress distribution of the following spread footing when: A) N =" kN) 70 B)…

A: Solution: Given: B = 10 L = 3 m Moment = 10 kN-m

Q: 8 in. 8 in. 9 in. 12 in. 4 in.

Q: A vertical steel bar shown in figure Q1 is subjected to a compressive load of 75 KN. If the stress…

A: Given data Limit stress = 47 MN/m2 = 47 N/mm2 E = 200 GN/m2 = 2 × 105 N/mm2

Q: Determine the magnitude of the pin force at A. Assume W = 590 lb, a = 2.9 ft, b = 2.0 ft, r = 6 in.…

Q: A skier starts from rest on the 37° slope at time t = 0 and is clocked at t = 2.35 s as he passes a…

A: Answer : We are given θ= 37 t=2.35 s s =15 m Since coefficient of kinematic friction is asked we…

Q: Situation 1: In the given beam below, determine the following: Use both Slope and deflection at…

Q: 300 mm B 600 mm C 400 N·m 600 mm D 200 N·m A 800 N·m

Q: AURS External support reactions: RA= L1 RC = Consider the following values in the given beam above:…

Q: Provide

A: As there are multiple questions posted, according to the guidelines, only the first three are being…

Q: a traverse ABCDE the following bearings are observed ind out their included angles and check it.…

Q: Vertical Reaction at Support C (KN) Note: El is constant, no support settement. 400k 150k ↓ ↓ t₂ 2m…

A: Given data

Q: 2. The jet passes through a point A, as shown. Calculate the flow rate. Assume the flow is…

Q: For low cost housing design which is most preferred material to be used? (factors to be considered:…

A: Not only does the availability of affordable construction materials provide access to permanent…

Q: The force P is applied to the 58-kg block when it is at rest. Determine the magnitude and direction…

A: Given : Inclined block with mass 58 Kg. Coefficient of static friction = 0.23 Coefiicient of…

Q: Use Virtual Work Method to calculate the horizontal deflection at the 90 kN load for the frame shown…

A: Virtual Work Method:∆=∫0LMmEIdxM- Moment due to real force in the systemm- Moment due to virtual…

Q: External support reactions: RA= L1 RC = Consider the following values in the given beam above: L1 =…

Q: 2. From the tabulation below determine if the column is safe to carry axial & bending load Yield…

A: Pr = 200KN Mrx = Mry = 16KNm. fy = 248MPa

Q: (a) Calculate the thing of protection of the block against sliding if the density of the rock is…

Q: Situation 5: A barge is pulled by two tugboats. If the esultant of the forces exerted by the…

A: Given that the resultant force is 5000lb along the axis of barge. Let T1 and T2 are tension in ropes…

Q: Question 4 The figure below shows an undersea structure with a shape that can be approximated as one…

Q: Two springs of different properties, A and B, are connected in series that support a force P as…

Q: 10

A: Given:- F.S.=1.6 To find:- most economical section

Q: A thick cylindrical pressure vessel of inner diameter D, and outer diameter D is subjected to an…

A: The hoop stress and the radial pressure variation can be obtained using Lame's equation:

Q: 2) In the figure shown, it is required to determine the shear and moment at x₁, and x2. Draw the…

A: The given beam is a cantilever beam with point loads and a triangular load acting on half of it's…

Q: * Ignore Internal Strain Energy due to axial load and shear. A (pinned) 15 ff 2 k/ff V C (hinge) V…

Q: Find normal stress at point P

A: Given, Figure shows a machine frame, Horizontal force,F= 600 NParallel to z-direction.Thickness,T=…

Q: magnitude of the velocity.

A: Given data, Velocity,V= 35 m/sin the horizontal direction Where,Wheel radius is = rCalculate…

Q: Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 300 lb…

A: Given data in question Load Angle To find out Components

Q: The simply supported beam is made of timber that has an allowable bending stress of o = 6.72 MPa and…

Q: Situation 7: Considering the same figure as above, the towline exerts a force P =4 kN at the end of…

Q: 3 4 5 the limiting diameter thickness ratio "D/t" of hollow circular section in flexure for compact…

A: Answer: We know from AISC Manual section B4.1 deals with classification of sections for Local…

Q: 12 13 14 the limiting width thickness ratio "bf/2tf" for flexure in flange of Tee sections for non…

A: Compact Section:- A compact section is one that can obtain the plastic moment through web or flange…

Q: An sewer pipe (n=0.015) is designed to carry a flowrate of 83.5 cfs when the pipe flows 0.90 full.…

Q: G 0.85), find the total energy head (m) at point A with respect into a datum at the pump. Suction…

A: According to given dataThe solution of the problem is given belowThe Energy Head would be -4.40…

Q: Solve it correctly please. I will rate accordingly with 4votes.

A: Given data:- Inner diameter, d= 4 inch Wall thickness, t=0.1 inch Internal pressure, P=50 ksi Axial…

Q: Analyze the frame shown

A: Truss: Truss is a pin joint structure subjected to loading only on joint and there is only one force…

Q: There are two points, A and B, whose elevations above datum are h=1380 ft and hg=930 ft and whose…

Q: The force P is applied to the 44-kg block when it is at rest. Determine the magnitude and direction…

Q: Prob. 4.3-10. The solid circular shaft of diameter d in Fig. P4.3-10a has a twist rate of dd/dx = 0,…

A: Answer We are given Solid shaft diameter = d Tubular shaft outside diameter = do Tubular shaft…

Q: 41. The pipeline shown in Figure P8.41 branches into two Mines as shown. The pipe diameters,…

A: Given :

Q: Determine the absolute maximum shear stress developed in the beam Express your answer to three…

A: Given : Rectangular cross-section b = 3 in d = 6 in For the given loading in the beam, maximum…

Q: Please solve, include the diagrams, and do not copy from other bartleby answers. Handwritten…

A: Write the shear and moment equations for the beam loaded as shown, then sketch the shear and moment…

Question

The actual velocity in the contracted section of a jet of liquid flowing from a 50mm diameter orifice is 9.21 m/s under a head of 4.57 m.

what is the value of coefficient of velocity?

Ans in 4 decimal places.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Mass and mass related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A jet plane taking off creates a noise with a magnitude of approximately 125 dB. What is the magnitude of the pressure disturbance (in Pa)?
A plugged dishwasher sink with the dimensions of 14 in. 16 in. 6 in. is being filled with water from a faucet with an inner diameter of 1 in. If it takes 220 seconds to fill the sink to its rim, estimate the mass flow of water coming out of the faucet.
What is the theoretical velocity of a jet of water flowing out of a square orifice in a large tank if the center of the orifice is 600 mm below the water surface?
Show complete solution. Units must be included in all calculations. All numerical values should be rounded off to the nearestthousandths. 2.If the velocity in a 12-in pipe is 1.65 ft/s, what is the velocity in a 3-in-diameter jet issuing from a nozzleattached to the pipe?
A liquid is flow throw Rotameter to a tank of size ( L x W x H ) and it is required to full the tank to level of H as shown in Figure . What time is required to full the tank by this liquid ? What time is required to drop the liquid in the tank to from level H to D by rectangular notch ?
Fluid mechanics- Bernoulli's Equation along a streamline: The flow-metering device shown consists of a stagnation probe at station 2 and a static pressure tap at station 1. The velocity at station 2 is twice that at station 1. Air with a density of 1.2kg/m3 flow through the duct. A water manometer is connected between the stagnation probe and the pressure tap, and a deflection of 10cm is measured. What is the velocity at station 2?
Determine whether the flow is turbulent or laminar if a fluid flows at 0.001?^3/? through a 100mm diameter pipe.
A cylindrical tank has a diameter of 1.4 m. and a total height of 1.8 m. It contains water to a depth 2/3 of its total height. What will be the required angular velocity (in rad/s) such that half of its content will be spilled out? A. 9.80 rad/s B. 10.40 rad/s C. 14.00 rad/s D. 8.09 rad/s
Imagine that the water level in Problem 8.34 rises at a rate of 0.1 cm/s. Knowing the diameter of the tank is 15 cm, what is the average velocity of the water leaving the tank?
An open cylindrical tank having a radius of 0.45 m. is filled with water at a depth of 0.68 m. If it is rotated about its vertical axis to a velocity of 103 rpm, what should be the height (in meters) so that no water will be spilled out? Round off to two decimal places.
An open cylindrical tank 3m high and 1.5m in diameter contains 2m high of water. If the cylinder rotates about its geometrical axis, what constant angular velocity can be attained if the depth of water at the center is 0.5m? Unit of the Correct Answer: rad/sec Decimal Places required in the final answer: 3
1. A liquid having a Reynolds Number of 1900 flows thru a 200 mm diameter pipe, 150 m long. The head loss of the pipe due to friction is 22 m. Compute the rate of flow in liters/sec. a. 129.857 b. 291.785 c. 192.587 d. 219.875