Determine its required cross-sectional dimension b in mm. The beam is subjected to the loadingshown. If the allowable shear stress isTallow = 75 MPa and the allowablebending stresses are o, = 50 MPa incompression and of = 120 MPa intension, determine its required cross-sectional dimension b.25 kN/m20 kN/m10 kNVDVG30 kN - m1 m0.75 m1 m0.5 m0.50.25 m2/31/31/2

Answered: Image /qna-images/answer/243b1400-2824-4f81-b7d1-f0904e50d6d7.jpg

The beam is subjected to the loading shown. If the allowable shear stress is Tallow = 75 MPa and the allowable %3D bending stresses are o̟ = 50 MPa in compression and of = 120 MPa in %3D tension, determine its required cross sectional dimension b. 25 kN/m 20 kN/m 10 kN 30 kN - m 1m 0.75 m 1m 0.5 m -0.25 m lo 1/2

The beam is subjected to the loading shown. If the allowable shear stress is Tallow = 75 MPa and the allowable %3D bending stresses are o̟ = 50 MPa in compression and of = 120 MPa in %3D tension, determine its required cross sectional dimension b. 25 kN/m 20 kN/m 10 kN 30 kN - m 1m 0.75 m 1m 0.5 m -0.25 m lo 1/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the moment equation for section AB. What is the bending moment (in kN-m) at x = 2.35 m? Determine the shear equation for section BC. What is the shear force (in kN) at x =8.15 m?
The beam is to be cut longitudinally along both sides as shown. If it is made from a material having an allowable shear stress of tallow = 75 MPa, determine the maximum allowable shear force V that can be applied before and after the cut is made.
Using portal method, Calculate for the shear force in kN at member FC a = 12.6 kN, b = 27.2 kN, c = 3.5 m, d = 5.0 m, e = 5.4 m
1. Find the resultant of tension F and Ta. 27.6 kNb. 37.2 kNc. 33.7 kNd. 44.6 kN2. What is the angle that their resultant makes with the horizontal rod OA? a. 28 degb. 37 degc. 33 degd. 44 deg3. Find the weight, W to prevent uplift. Use a factor of safety of 2.5. a. 49.23 kNb. 42.86 kNc. 59.51 kNd. 44.72 kN
Given the following data:Cross section: 50mm x 75mmP = 200 kNθ = 15 ° with the x-axis Find the shear stress (in MPa) on plane A-A.
The Beam has a span of 9 m, fixed at both ends and carries a uniformly distributed load of w = 25 kN/m throughout its length. The beam is W 16 x 77 with the following properties: bf = 260 mm tf = 19.3 mm d = 420 mm tw = 11.6 mm Ix = 462. 02 x 106 mm4 Iy = 57.44 x 106 mm4 a. Calculate the maximum bending stress in the beam, in MPA. b. Calculate the average shearing stress in the web, in MPa.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
A prismatic continuous beam is shown. The flexural rigidity is 100 000 N. m². The problem maybe solve using superposition method. 1. Determine the vertical midspan deflection due to the given loads in millimeters if the middle support is removed. a. 5.83 b. 6.20 c. 4.95 d. 7.17 2. Determine the vertical midspan deflection due to an upward unit load at midpoint in millimeters if the middle support is removed. a. 0.513 b. 0.678 c. 0.245 d. 0.360 3. Determine the reaction at the middle support in Newton’s. a. 29.5 b. 13.8 c. 36.2 d. 47.0
Determine the maximum bending stresses for a rectangular beam (20x40cm) subjected to a bending moment Mz = 60 kN.m.
If the beam is subjected to a shear of V=30KN, determine the transverse shear stress at the neutral axis, and points A and B. USE THE BOTTOM OF THE BEAM AS YOUR REFERENCE WHEN DETERMINING THE LOCATION OF THE NEUTRAL AXIS.
31 -Loading status in figure q= 4 kN ⁄ m, P = 48 kN in the bar dimensions L= 2 m and e= 0.5 m. The cross-sectional effects at point E will be calculated. A is fixed, B is sliding joint bearing. Accordingly, the shear force at point E T=? a) 2B) 4C) 14D) 0E) 6
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please