The beam is supported by a pin support at point A and a rocker support at point B, and the length is /= 6.6 ft. It has a cross section shown in the image with h = 7.7 in. It is subjected to a uniformly distributed load with load intensity w = 460 lb/ft, and a couple moment of 1500 lb-ft as shown. Point C is located immediately to the right of the couple moment, and the vertical location of point C is also shown in the cross section. If the location of point Cis indicated on the cross section, and its state of stress can be represented on the volume element as shown, determine the shear stress Txy (in the unit of psi). Negative sign must be included if the direction is opposite to what's shown in the state of stress image. A Exy Ox W 1500 lb ft 6 ft- + B 30° 1in. 2 in. с 6 in. h 1in. 1in. Please pay attention: the numbers may change since they are randomized. Your

The beam is supported by a pin support at point A and a rocker support at point B, and the length is /= 6.6 ft. It has a cross section shown in the image with h = 7.7 in. It is subjected to a uniformly distributed load with load intensity w = 460 lb/ft, and a couple moment of 1500 lb-ft as shown. Point C is located immediately to the right of the couple moment, and the vertical location of point C is also shown in the cross section. If the location of point Cis indicated on the cross section, and its state of stress can be represented on the volume element as shown, determine the shear stress Txy (in the unit of psi). Negative sign must be included if the direction is opposite to what's shown in the state of stress image. A Exy Ox W 1500 lb ft 6 ft- + B 30° 1in. 2 in. с 6 in. h 1in. 1in. Please pay attention: the numbers may change since they are randomized. Your

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
For the truss in Figure P8.3, compute the horizon-tal and vertical components of the displacement of jointC. The area of all bars = 2500 mm2, and E = 200 GPa.
Problem Number 1: In the given loaded beam determine the resultant force, R and its location from the pointA as it intersects the line AB.
Determine the vertical displacement of joint C of the truss as shown. Assume that A = 0.5 in2 and E = 29(103) ksi.
Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm and Acr = 9,280 mm. The distances between various points on the bars are shown in the figure. Determine the vertical displacements & and dp of points A and D, respectively.
If E=200 GPa. a. Determine the slope at support A. b. Determine displacement at 8m from the left support.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 4.2 ft, b = 3.3 ft, P = 22 kips, and w = 2.7 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction provided by the ground to be uniformly distributed. Let a = 5.0 ft, b = 4.5 ft, P = 21 kips, and w = 3.0 kips/ft. Label all significant points on each diagram. Determine the maximum value of (a) the internal shear force and (b) the internal bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
A simply supported beam carries a concentrated load of 31 kN at 7 meters from the left support (1 meters from the right support). Use EI = 80,000 kN-m2. Solve for the slope at the left support in degrees.
If P = 26 and M = 5.74, Determine the Axial Force at point B of the Beam shown.
1) Draw the shear force and bending moment diagram of the beam in Figure Q2(a), (b), and (c). The dimension of the beam are as shown in Figure Q2(a).