The beam shown in the figure supports a concentrated load of 15 kN and а uniformly distributed load of 4 kN/m. It has a selfweight of 2 kN/m. A B 3m 3m 3m What is the maximum negative shear at point B? Section Section What is the maximum positive moment at point B? Section What is the maximum reaction?

The beam shown in the figure supports a concentrated load of 15 kN and а uniformly distributed load of 4 kN/m. It has a selfweight of 2 kN/m. A B 3m 3m 3m What is the maximum negative shear at point B? Section Section What is the maximum positive moment at point B? Section What is the maximum reaction?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tower crane is used to hoist a 2-Mg load upwardat constant velocity. The 1.5-Mg jib BD and 0.5-Mg jib BChave centers of mass at G1 and G2, respectively. Determinethe required mass of the counterweight C so that the resultantmoment produced by the load and the weight of the towercrane jibs about point A is zero. The center of mass for thecounterweight is located at G3.
For questions 2A and 2B, refer to the load and shear diagrams below. 2A. What is the slope of the shear diagram of the line from B to C?A.15 KN/mB.16 KN/mC.24.46 KNmD.11.26 KNmThe change in moment [KNm] of the diagram above from point A to the concentrated load is nearest toA.98B.99C.100D.101
Thehorizontalbarshown(Length=15.0 feet)restsonsmoothinclines.Computethedistancexat which load T= 250 lbs should be placed from point B to keep the bar horizontal?
Blocks B has a mass of 20 kg and block C has a massof 15 kg. The coefficient of static friction at thecontacting surfaces is 0.2. Block A is suspended by arope that passes over a fixed cylinder and is attachedto block B. The coefficient of static friction betweenthe rope and the cylinder is 0.25. What is the largestmass block A can have without causing block B to slipthe left?
The tensions of the ropes used in pulling a boat along a river by 2 carabaowhich are on opposite side and walking parallel to the river bank are 400Nand 360N. The angle between the ropes is 600. Find the resultant of thepulling force on the boat. Also, determine the angle that separates eachof the rope from the boat.
Home Work H.W(l Blocks A.B and C have weights of 50N.25N and 15N respectively. Determine the smallest horizontal force P that will cause impending motion. The coefTicient of static friction between A and B is p=0.3, between B and C is H=0.4. and between block C and the ground is p=0.35.(Ans: P=45N)
The roof is supported by cables as shown in the photo. If the cablesexert forces FAB = 100 N and FAC = 120 N on the wall hook at A asshown , determine the resultant force acting at A. Expressthe result as a Cartesian vector.
The boom OAB pivots about point O, while section AB simultaneously extends from within section OA. Determine the velocity and acceleration of the center B of the pulley for the following conditions: θ = 28°, θ˙ = 3 deg/sec, θ¨ = 4 deg/sec2, l = 9 ft, l˙ = 1.8 ft/sec, l¨ = -3.8 ft/sec2. The quantities l˙ and l¨ are the first and second time derivatives, respectively, of the length l of section AB. Express your answers as vectors in the er and eθ directions.
a = 4.5 m b = 33.0 kN/m c = 13 kN
The tripod shown is to support a vertical load W and horizontal load P at point D. The legs of the tripod rest on a level rough surface at points A, B and C. If W=150N, P=50N, a = 0.5m, b =0.75m. c=1.125m, d=1.5m, 19. Determine the force acting on leg AD. Determine the force acting on leg BD.
Given T = 0.6, SDS = 1.67, SD1 = 0.87, W = 1000 (kips), R = 8, and Ie = 1, find Base Shear V in kips to the nearest kip.
Rectangular load C to D = 200lb/ft