The belt as shown below, moves at steady velocity V and skim at the top of a tank of oil of viscosity μ. Assuming a linear velocity profile, then which of the following expression is correct regarding power, P. Assume B moving belt width h is the oil depth and air drag is neglected. Oil depth, h moving belt width B.

The belt as shown below, moves at steady velocity V and skim at the top of a tank of oil of viscosity μ. Assuming a linear velocity profile, then which of the following expression is correct regarding power, P. Assume B moving belt width h is the oil depth and air drag is neglected. Oil depth, h moving belt width B.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

A solid cone of angle 2θ, mass (m), base radius (r0), and density (ρc), is rotating with angular velocity (w0) on its conical seat. The clearance (h) is filled with oil of viscosity (μ). Neglecting air resistance, determine: a) an expression for the moment (M) as a function of r0, w0,μ,θ, and h. b) an expression for the angular velocity (w) for t≥0 as a function of w0,μ,θ,h, r0,m and t if an external torque is not applied. If the radius of gyration of the cone is 16 cm, determine: c ) the value of the angular momentum and velocity if w0=60RPM,h=0.05mm,θ=30°,μ=0.98cPoise , m=20kg, t=2.0s
If a stream flowing at velocity U past a body of lengthL causes a force F on the body that depends only on U , L ,and fluid viscosity μ , then F must be proportional to(a) ρUL/μ, (b) ρU2L2, (c) μU/L, (d) μUL, (e) UL/μ
plzz help meeeeeeeeee The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
Find the surface tension of the water droplet of 30 mm diameter when the inside pressure is 3.5 N/m2 The surface tension in N/m is
A lubricating oil of viscosity u undergoes a steady sheer between a fixed lower plate and an upper moving plate at a speed V. Distance between the plate is T. Show that the linear velocity results results if the fluid does not slip at either plate
2.) We are on the space station, so there is no effective gravity. In a small fluid experiment, a small spherical bacteria of 1 mm radius is moving at a speed of +1.50 mm/second horizontally in the fluid. The bacteria has a density of 1500. kg/m^3. (3a) Draw a free-body diagram, labeling all forces and show the likely direction of Fnet (3b) What is the mass of the bacteria? (3c) If the value of the viscosity is 1.25 kg/m/s, then what is the net acceleration experienced by the bacteria at that moment.
The belt in Fig. 2, moves at a steady velocity V in the tank of oil , as shown. Assuming a linear velocity profile in the oil, determine the force F required to belt-drive at velocity of 7 m/s. if you know that the viscosity of oil is 0.29 kg/(m.s). *
Q. An open container of oil rests on the flatbed of a truck that is traveling along a horizontal road at 65 mi/hr. As the truck slows uniformly to a complete stop in 4s, what will be the slope of the oil surface during this period of constant acceleration? Show solution.
The air bubble formed by explosion inside water perform osillations with time period T which depends onpressure p), density (p) and on energy due to explosion (E). Establish relation between T, p. E and p.
The belt in the Ögure moves at steady velocity V and skims the top of a tank of oil having viscosity. (a) Develop and expression for the required belt drive power in terms of h, L, b, V , and . Recalthat, for steady motion, power is equal to force velocity.(b) What power is required if the belt moves at 5 m/s over SAE 50W oil ( = 0:86 kg/ms) withh = 2 cm, L = 2 m, and b = 0:5 m
Find the kinematic viscosity of an oil having density of 980kg/m^2 when at a certain point in the oil, the shear stress is 0.25 Pa and the velocity gradient is 0.3 m/s.
Three types of fluids stack in an open tank as shown in the picture. If the specific gravidties are sg1=1.00, sg2=2.00, sg3=3.00, and h1=1.00 m, h2=1.00 m, h3=1.00 m, calculate the gage pressure at location 4, P4(gage)=_________(kPa)