The belt is travelling to the right at some speed v, while the pipe is rolling without slipping at w = 1.2 rad/s as shown. If the center of the pipe G appears to an observer on the ground to move at 2 m/s to the left delermine the velocity of the belt v. Write the answer in m/s but do not write the units. 1.5 m Belt

The belt is travelling to the right at some speed v, while the pipe is rolling without slipping at w = 1.2 rad/s as shown. If the center of the pipe G appears to an observer on the ground to move at 2 m/s to the left delermine the velocity of the belt v. Write the answer in m/s but do not write the units. 1.5 m Belt

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.26P: The velocity vector of the boat has two components: v1 is the velocity of the water, and v2 is the...

See similar textbooks

Similar questions

A rifle at A is fired at a target at B. If the speed of the bullet is 1400 ft/s, determine the rectangular form of the velocity vector v.
The rod OA rotates in the horizontal plane such that =0.66t3 radian, and collar B is sliding outward along OA so that r=114t2 mm. If in both cases t is in seconds, determine the radial component of velocity (mm/s) of the collar when the collar is 128 mm from O. Round off only on the final answer expressed in 3 decimal places. DONT ROUND OF IN THE ENTIRE SOLUTION, ONLY IN THE FINAL ANSWER
The rod OA rotates in the horizontal plane such that 0.44t3 radian, and collar B is sliding outward along OA so that r=79t2 mm. If in both cases t is in seconds, determine the transverse component of velocity (mm/s) of the collar when the collar is 117 mm from O. Round off only on the final answer expressed in 3 decimal places.
The rod OA rotates in the horizontal plane such that 0.42t3 radian, and collar B is sliding outward along OA so that r=24t2 mm. If in both cases t is in seconds, determine the magnitude of velocity (mm/s) of the collar when the collar is 94 mm from O. Round off only on the final answer expressed in 3 decimal places.
The horizontal motion of the plunger and shaft is arrested by the resistance of the attached disk which moves through the oil bath. The velocity of the plunger is v0 = 3.1 m/s in the position A where x = 0 and t = 0, and the deceleration is proportional to v so that a = -kv where k = 0.32 s-1. Find (a) the velocity when t = 2.9 s, (b) the position x when t = 2.9 s, (c) the velocity when x = 4.2 m.
Determine the angular velocity, in rpm, of the rotating drum which results in loss of contact between the clothes and the drum at 1.0239 rad. Assume that the small vanes prevent slipping until loss of contact. Round your answer to 2 decimal places
The velocity of aparticle which moves along the x-axis is given by x = 40-3t² (m/s) where t is in seconds. Calculate the displacement Ax of the particle during the interval from t=2sec to = 4 sec.
The cable at A is being drawn toward the motor at vA = 8 m/s. Determine the velocity of the block.
Consider the portion of an excavator shown. At the instant under consideration, the hydraulic cylinder is extending at a rate of 5 in./sec, which is decreasing at the rate of 2 in./sec every second. Simultaneously, the cylinder is rotating about a horizontal axis through O at a constant rate of 13 deg/sec. Determine the velocity v and acceleration a of the clevis attachment at B. Write the velocity and acceleration as vectors.Answers:v = ( er + eθ) in./seca = ( er + eθ) in./sec2
Determine the velocity of the center of gravity G of the connecting rod at the instant theta = 36 degrees. Enter the x and y components of the velocity in inches per second to three significant figures separated by a comma.t
If the block at C is moving downward at 4 ft/s, determine theangular velocity of bar AB at the instant shown.
The cone falling with a speed v0 = 2 m/s strikes and penetrates the block of packing material. The acceleration of the cone after impact is a = g − cy2 where g is acceleration of gravity, c is a positive constant and y is the penetration distance. If the maximum penetration depth is observed to be ym = 0.10 m determine the constant c in 1/ms2.