The bent rod is supported by a thrust bearing at point A and a journal bearing at point D. The 100 kg weight of a large bucket of apples is supported by the cable, wrapped around the drum. a) Draw a free-body diagram of the bar. b) Find the force P necessary to hold the bent rod in 0.1 m 0.3 m place. D |0.5 m 0.15 mx 0.3 m 100 kg c) Find the reactions at the 20 0.3 m thrust bearing at point A. d) Find the reactions at the journal bearing at point D

The bent rod is supported by a thrust bearing at point A and a journal bearing at point D. The 100 kg weight of a large bucket of apples is supported by the cable, wrapped around the drum. a) Draw a free-body diagram of the bar. b) Find the force P necessary to hold the bent rod in 0.1 m 0.3 m place. D |0.5 m 0.15 mx 0.3 m 100 kg c) Find the reactions at the 20 0.3 m thrust bearing at point A. d) Find the reactions at the journal bearing at point D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.10P: Find support reactions at 4 and Band then use the method of joints to find all member forces. Let b...

See similar textbooks

Similar questions

A transmission cable 300 m long, weighs 600 kg. The tensions at the ends of the cable are 400 kg and 450 kg. Find the distance of its lowest point to the ground. Choices: 150m ,153m , 148m , 145m
A 40 kg-mass hangs from the end of a uniform beam. The beam is 6.0 m long and has a mass of 60 kg. The beam is supported at the left end by a hinge at the wall and by a cable at the right end. The other end of the cable is tied to the wall at a point 4.0 m above the left end of the beam. (g = 9.81 m/s² )A. Draw the FBD;B. Find the tension (T) in the supporting cable in Newtons; andC. Find the reaction force (R) of the hinge on the beam ( magnitude and direction).
1-A bar of square cross section is subjected to point loads of P1, P2, P3 and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 110 kN, P2 = 210 kN & P4 = 190 kN. Also, determine the stresses in each section & the net change in the length of steel bar. square of size a1=50mm, L1=30 cm, size a2 = 40mm, L2=39 cm, size a3=50 mm & L3 =32 cm Take E = 166 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is
nonuniform beam 4.50 m long and weighing 1.40 kNmakes an angle of 25.0° below the horizontal. It is held in position bya frictionless pivot at its upper right end and by a cable 3.00 m fartherdown the beam and perpendicular to it . The center ofgravity of the beam is 2.00 m down the beam from the pivot. Lightingequipment exerts a 5.00 kN downward force on the lower left end ofthe beam. Find the tension T in the cable and the horizontal and verticalcomponents of the force exerted on the beam by the pivot. Start bysketching a free-body diagram of the beam.
A uniform bar 6 m long is held by ropes at the ends making angle 60° and 30°, respectively, with the horizontal. A weight of 400 N is hung 1.0 m from the left end where the 60° rope is attached. Find the tension in the rope and the weight of the bar.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?
Q/ Find the reaction forces at A and B, (A pin connection and B roller connection)? 120N/m
Find the support reactions for the distributed load
A 4.20 m long (L) steel pipe has a mass of 450 kg and is lifted by a crane attached to cable CD. Point C is attached to each end of the pipe at A and B of the steel pipe. The length AC is 3.25 m and the length BC is also 3.25 m (i.e., length AC = BC). Using g = 9.81 m/s2, calculate the tension in sling AC and give your answer in newtons (N) to the nearest newton.
Weight W is supported by pipe AO and cables AB and AC. Find the compressive force in member AO and the tensile force in cables AB and AC, given: W = 400 N, AY = 7 m, AZ = 9 m, BX = 9 m, BY = 7 m, CX = 9 m, CY = 12 m
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where Mo = 10,800 kip-in, P = 1205 lb, F = 1.25 kip, Wa = 2750 lb/ft, Wb = 1.055 kip/ft, a = c = 7 ft, b = 12 ft.
The figure shows the cross section of three cylinders, 1m long, given the density of steel 500 lbs/cu.ft. Find the reactions between all of the cylinders and the ground in lbs. Units are in feet.