The block shown is made of a magnesium alloy for which E=X2GPaand ϑ=0.35. Knowing that σx= X1 MPa, determine (a) the magnitude of σyfor which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.

The block shown is made of a magnesium alloy for which E=X2GPaand ϑ=0.35. Knowing that σx= X1 MPa, determine (a) the magnitude of σyfor which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 2ETSQ

See similar textbooks

Similar questions

1 Proof that a solid aluminum block of 4 mm x 3 mm x 3 mm, such as shown in FigureQ1 (a), can float on water at 20 °C due to the effect of surface tension. The density ofthe aluminum block is 2700 kg/m3. Determine the contact angle. 2. A solid alloy cylinder having a diameter of 6.48 cm slides downward at a terminalvelocity of V through a vertical pipe. The downward motion is resisted by an oil filmbetween the piston and the pipe wall. Determine the oil viscosity when the velocityV is 5 m/s. The inner diameter of the vertical pipe is 6.5 cm, and the alloy density is3500 kg/m3.
The block shown is made of a magnesium alloy for which E = 45 GPa and ν = 0.35. Knowing that σx = -180 MPa, determine (a) the magnitude of σy for which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
In shown figure the aluminum is subjected to a thermal stress where T1 is 21.957 deg. C and T2 is 87.860 deg. C. Determine the required diameter (mm) of the steel rods to limit the expansion of the aluminum just 3.238 mm if the thermal coefficient of aluminum is 24.650 x10^-6 Where: H1 = 2000.392 mm H2 = 2047.231 mm H3 = 1999.692 mm Aal = 2288 mm^2 Eal = 70.018 GPa Est = 202.930 GPa
The polyvinyl chloride bar is subjected to an axial force of 900 lb. If it has the original dimensions shown, determine the value of Poisson’s ratio if the angle u decreases by Δu = 0.01° after the load is applied. Epvc = 800(103) psi.
An air compressor used by a mechanic for filling air in tyre is cylindrical in shape which has internal diameter and thickness of 600mm and 20mm respectively. If the compressor is subjected to an internal pressure of 30N/mm2 determine the increase in volume of the cylinder. The cylindrical compressor has a length of 2m and the material used m manufacturing the cylinder has elasticity,E=2*105N/mm2 and Poisson's ratio,1/m= 0.3.
a.) Find the bulk modulus of elasticity of a liquid if a pressure of 150 psi applied to 10 ft3 of the liquid causes a volume reduction of 0.02 ft.3. b.) Find the capillary rise in the tube for a water-air-glass interface (θ = 0°) if the tube radius is 1 mm. Surface tension is 0.0728 N/m.
the external and internal diameters of hollow cylinder are 115mm and 99mm respectively. when the cylinder is compressed by an axial force of 180kn the outer diameter of cylinder increases by 115.5 x 10-4 mm . determine youngs modulus of elasticity 2x105 N/mm2 a) the increase in the inner diameter . b) the increase in the wall thickness and c) Poissons ratio of the material of the cylinder
Determine the stability and determinacy of the figures.
A steel block has a length of 80 mm, width of 60 mm and thickness of 40 mm. The block is subjected to a uniform hydrostatic pressure of 180 kPa on all its faces. Modulus of elasticity E=200 GPa, Poisson’s ratio ?= 0.29. a.) Determine the bulk modulus of steel, b.) Determine the dilatation (e) of the material if e is the negative of the ratio of load to bulk modulus., and c.) Determine the change in volume of the steel block.
the cross-sectional area of the bar 1 of the two bars supported on the left and right sides is 1.2 cm^2, the coefficient of thermal expansion is 20.9 10^(-6)/K; The cross-sectional area of bar 2 is 3 cm^2 and its coefficient of thermal expansion is 25.4 10^(-6)/K. Since the modulus of elasticity of the material is 207 GPa, these two bars are heated to 99 °C.a) What will be the change in length (mm) of bar 1?b) What is the stress in bar 1 in MPa?c) What is the stress in bar 2 in MPa?
A piston rod is subjected to a maximum compression load of 32000 lbs. and is 20 in.long. The material for the rod has a yield strength of 73 ksi. The Rankine’s constant canbe taken as 0.00026. What would be the diameter of the rod for a factor of safety of 4?a. 1.61 inb.0.97 inc. 1 ind.1 3/4 in.
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.