The cantilever beam in Figure 6.3 is subjected to a uniformly distributed load. The flexural stiffness of the beam is doubled from the fixed-end to the midspan to minimize deflection. Determine: a. the equations of the elastic curve, b. the slope and deflection at B, c. the slope and deflection at d. the maximum w. that can be applied if the maximum allowable deflection is L/360. and

The cantilever beam in Figure 6.3 is subjected to a uniformly distributed load. The flexural stiffness of the beam is doubled from the fixed-end to the midspan to minimize deflection. Determine: a. the equations of the elastic curve, b. the slope and deflection at B, c. the slope and deflection at d. the maximum w. that can be applied if the maximum allowable deflection is L/360. and

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam is loaded as shown in the figure. Assume El is constant. Determine the deflection at midspan in terms of El using Area Moment Method.
A cantilever beam AB is loaded as shown in Figure 1. EI is constant for the beam. L = 2.7 m and P = 8.9 kN. Write down your L and P values and answer parts a to c below. (a) Using the moment area method, determine the slope of the beam at B. (b) Using the conjugate beam method, determine vertical deflection at B. (c) Draw the free body diagram (FBD) of the virtual force system for the virtual work method to determine the vertical deflection at the mid-span of the beam. (Note: No calculations are required and show only the FBD).
Compute the slope at support A and the deflection at B in Figure P8.18. EI is constant. Express your answer in terms of E, I, L, and M.
For the beam shown, EI = Constant. Determine the following: A. Slope at B B. Deflection at C C. Location of the maximum deflection D. maximum deflection
A continuous beam is loaded as shown in the figure. Assume E and I are constant and userelative stiffness K. Using the slope deflection method: -Determine the moment at B in kN-m.
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the beam, (b) the maximum deflection, and (c) the slope at A. Assume that EI is constant for the beam. Let w = 14 kN/m, L = 4.5 m, E = 180 GPa, and I = 130 x 106 mm4. Part 1 Draw a free body diagram of the beam and solve the reaction forces Ay and By. Forces are positive upwards. Answer:Ay = kNBy = kN Part 2 Cut a cross-section through the beam at any point and draw a free body diagram. Determine the internal bending moment M(x). The diagram shows M(x) in its positive direction. Your answer may be negative. Check your equation by solving for M at x = 2.3 m.Answer:M(x = 2.3 m) = kN·m
Determine the displacement at C of the beam in this Figure using Conjugate Beam. E- 29,000 ksi and I=600 in.
The simply supported beam in the figure is loaded by a concentrated load at B and a clockwise moment at C. Draw the shear force and bending moment diagrams by area method. Neglect the weight of the beam.Please show complete solution
BP1: A cantilevered beam of constant EI and length L has a rectangular distributed load q over its length. Use integration method to find deflection. Begin at M(x) and proceed to y(x). A)Solve the deflection of the free end left to right B)Solve again but right to left
Determine the slope at A and B and the deflection at C for the simply supported beam shown in the figure. EI is contant. Use conjugate beam method.
A beam is shown in the figure below, and the flexural stiffness of the beam section is constant EI:(a) Use the Moment-area Method to obtain the Slope of Point A after deformation and the vertical displacement of Point C (Deflection)(b) Use the conjugate beam method (Conjugate Beam Method) to obtain the slope (Slope) after the deformation of point A and the vertical displacement (Deflection) of point C *The correct answer is 24 kN-m2/EI clockwise and 58.7 kN-m3 /EI down, but I need to calculate steps, thanks
A simply supported beam is loaded as shown in the figure. Assume El is constant. Determine the deflection at midspan in terms of El using virtual work method.