The cantilever bearn consists of a rectangular structural steel tube shape [E -29,000 ksi; I- 1640 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA - 160 kip-ft, P= 18 kips, LAB - 4.7 ft, Lec-7.1 ft. MA A LAB LBC Answer: (a) VA= in. (b) VB " in.

The cantilever bearn consists of a rectangular structural steel tube shape [E -29,000 ksi; I- 1640 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA - 160 kip-ft, P= 18 kips, LAB - 4.7 ft, Lec-7.1 ft. MA A LAB LBC Answer: (a) VA= in. (b) VB " in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
USING CONJUGATE BEAM METHOD Consider 150 mm x 200 mm (bxh) mm section and e = 80 GPa DETERMINE REACTION AT D Values: A = 9.4 M B = 5.5 kN/m C = 20 kN
Question 1) F=22 kN single load, M=26 kN.m moment and w=17 kN/m distributed load are acting on the beam whose loading condition is given in the figure. The length L is also given as L=5 m. The cross-sectional properties of the beam are; body height yg=239 mm, body thickness xg=17 mm, flange width xf=185 mm, flange height yf=15 mm. Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question 1-D) Find the moment of inertia of the beam section. (Do your operations by converting the lengths to meters. Take at least 4 digits for the decimal part of your result and use the expression E for the decimal part. Write it as 5E-3 instead of 0.005.)
F=11 kN single load, M=22 kN.m moment and w=5 kN/m distributed load act on the beam whose loading condition is given in the figure. The length L is also given as L=5 m. The cross-sectional properties of the beam are; body height yg=218 mm, body thickness xg=18 mm, flange width xf=190 mm, flange height yf=13 mm. Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the B level of the beam. According to this;
By DIM & MAM, determine the value of EIẟ at midspan for the beam loaded as shown. Take note that L, a, b, c, d, e are in m, P1 & P2 are in KN, and W is in KN/m.
A cantilever beam AB with a circular crosssection and length L = 750 mm supports a loadP = 800 N acting at the free end (see figure). Thebeam is made of steel with an allowable bendingstress of 120 MPa.(a) Determine the required diameter dmin (figurepart a) of the beam, considering the effect of thebeam’s own weight.(b) Repeat part (a) if the beam is hollow with wallthickness t =d /8 (figure part b); compare thecross-sectional areas of the two designs.
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
draw the v and m diagram of the continuous beam shown below. determine the value of EIy
Calculate the slope and deflection atB and E of the beam and loadings shown using unit load method. The section of the beam is tubular with outer diameter of 500mm and inner diameter of 200mm. Take E=20GPa.
From the given beam loaded as shown, Let P = 12 kips, L = 6 ft, a = 3 ft. E = 29 x 10^6 psi, I = 722 in^4. use double integration method a. Equation of the slope b. Equation of the deflection curve c. Position of the maximum deflection at segment AB from point A d. Maximum deflection.
Determine thy vertical displacement (mm) of joint B. Support A is roller and support D is hinge. A=2500 mm2 E=200 GPa
A cantilever beam supports the loads shown. The cross-sectional dimensions of the shape are also shown. Assume a = 0.4 m, PA = 2.0 kN, PB = 6.0 kN, PC = 3.0 kN, d = 85 mm, bf = 105 mm, tf = 5 mm, tw = 9 mm. Determine: Calculate the moment of inertia for entire cross-section about its z centroidal axis.Answer: Iz = (106) mm4 Determine the maximum value of Q for the cross-section, where Q is the first moment of the area. Answer: Qmax = (103) mm3 Determine the maximum vertical shear stress.Answer: τmax= MPa At the location of the maximum positive moment, determine the maximum tension bending stress, σT+, and the maximum compression bending stress, σC+. Report the answers here using the correct signs according to the flexure formula (σC+ will be negative). Answers: σT+= MPa σC+ MPa At the location of the maximum negative moment, determine the maximum tension bending…