The circuit below involves a 90 V battery, three resistors (10N, 150, and 201), and three capacitors (0.015F, 0.03F, and 0.03F). The switch stays on position "a" for a long time to reach a stable state. At t = 0 the switch is quickly toggled to position "b". How long after the switch is moved to position"b" will the current through the 200 is equal to 0.9A. 150 100 90 V. :0.03F 0.015P F0.03F 20.00

The circuit below involves a 90 V battery, three resistors (10N, 150, and 201), and three capacitors (0.015F, 0.03F, and 0.03F). The switch stays on position "a" for a long time to reach a stable state. At t = 0 the switch is quickly toggled to position "b". How long after the switch is moved to position"b" will the current through the 200 is equal to 0.9A. 150 100 90 V. :0.03F 0.015P F0.03F 20.00

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.3P

See similar textbooks

Similar questions

The capacitors are iinitially uncharged, and the switch is initially open. a) When the switch is first closed, what is the current through R2?
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
When the switch is closed in above circuit, what is the voltage on the inductor, resistor R1 and R2 after 2.2us , assuming 0 V on the inductor to start?
The magnitude of the voltage applied to the electrodes of a welding machine can be adjusted in the circuit below. In the range of minimum and maximum value that variable value resistor can take What is the time interval that the capacitor will charge from 0 to 8 V?
Determine the currents IR1 and IR2, (show as positive values – actual current direction). Verify in Multisim using measurement probes or digital multimeter
a.) What is the resistance in the circuit a long time after the switch is closed? b.) What is the current through both resistors a long time after the switch is closed? c.) What is the current through the inductor a long time after the switch is closed?
C2 The next two questions refer to the following figure. The switch is initially open and both capacitors are initially uncharged. All resistors have the same value R, and both capacitors have the same value C. R2 R3 bat R1 ww (f) 1 pt. Immediately after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) Rị and R2 (v) R2 and R3 (vi) All have the same current (g) 1 pt. A long time after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) R1 and R2 (v) R2 and R3 (vi) None have current
The circuit in the figure below contains two resistors, R1 = 4.00kΩ and R2 = 5.00kΩ, and two capacitors, C1 = 4.00uF and C2 = 5.00uF, connected to a battery with emf E = 120V. If no charges exist on the capacitors before switch S is closed, determine the charge q1 on capacitor C1 1.00ms after the switch is closed. Determine the charge q2 on capacitor C2 1.00ms after the switch is closed.
A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 ms
The circuit in Figure has been connected for a long time. If the battery is disconnected, how does it take the capacitor to discharge to 1/20 of its initial voltage? Take R₁ = 2.00 Q, R₂=4.00 Q, R3-7.00 Q, R4 = 2.00 Q and C= 5.00 uF and ε = 14.0 V. (Your result must be in us. Include 2 digit after the decimal point and maximum of 2% of error is accepted in your answer.) E R₂ R₂ BA
Here you see a circuit with a battery, fully uncharged capacitor, C and a bulb. What would happen to that electric bulb in the circuit when you switch on the circuit? Moreover, what would be the consequences if you switch off the circuit when capacitor is fully charged? Answer step by step .answer must be correct. Do all calculation follow image.
A voltage of 6 cos(100rt) V is fed as y-input to a CRO. The waveform seen on the screen of the CRO is shown in the figure. The Y and X axes settings for the CRO are respectively