The component values in the passive filter circuit shown below are: C=10µF, L=1H, andR=10k2.+CVoutina. Derive an expression for the voltage transfer function, Vaue/V -expressions for the magnitude and the phase angle of that transfer function.Also, determineb. Classify the filter as LP, HP, BP or BS, and explain your reasoning.

Answered: Image /qna-images/answer/2bfbb6a2-c5a1-47db-9b51-3aff9c8f1618.jpg

The component values in the passive filter circuit shown below are: C=10¼F, L=1H, and R=10k2. Vin L out a. Derive an expression for the voltage transfer function, Vm/Vm. Also, determine expressions for the magnitude and the phase angle of that transfer function. ouf b. Classify the filter as LP, HP, BP or BS, and explain your reasoning.

The component values in the passive filter circuit shown below are: C=10¼F, L=1H, and R=10k2. Vin L out a. Derive an expression for the voltage transfer function, Vm/Vm. Also, determine expressions for the magnitude and the phase angle of that transfer function. ouf b. Classify the filter as LP, HP, BP or BS, and explain your reasoning.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The voltage transfer function for either high-pass prototype filtershown isH(s)=ss+1. Show that if either circuit is scaled in both magnitude and frequency, thescaled transfer function isH′(s)=(s/kf)(s/kf)+1.
Consider the circuit shown . 1. a) What is the transfer function, H(s)=Vo(s)/Vi(s), of this filter? 2. b) What is the cutoff frequency of this filter? 3. c) What is the magnitude of the filter’s transfer function at s=jωc?
The voltage transfer function of the prototype bandpass filtershown isH(s)=(1Q)ss2+(1Q)s+1. Show that if the circuit is scaled in both magnitude and frequency, thescaled transfer function isH′(s)=(1Q)(skf)(skf)2+(1Q)(skf)+1.
a ) Using 0.1 pF capacitors , design an active broadband first - order bandpass filter that has a lower cutoff frequency of 200 Hz , an upper cutoff frequency of 2000 Hz , and a passband gain of 0 dB . b ) Write the transfer function for the scaled filter . c ) Use the transfer function derived in part ( b ) to find H ( wo ) where wo is the center frequency of the filter . d ) What is the passband gain ( in decibels ) of the filter at wo ?
(a) as shown for a maximally flat second-order low-pass filter with fo =25 kHz, using the circuit as shown. Assume C =0.005μF.What is the filter bandwidth? (b) Use frequency scaling to change fo to 50 kHz.
RLC bandpass design： The target is to filter out the square-wave noise from the 120kHz sinsousidal signal using the RLC banpass filter (series LCR configuration). 1- Derive the transfer function for the following second order LCR filter. 2- Derive an expression for the resonant frequency and the quality factor of the filter. 3- The objective is to filter out the square-wave noise from the sinousidal 120kHz signal. The two closest frequency components of the square wave must be attenuated at least by a factor of √2. We suggest you to use either a 10 mH inductor. Calculate the required Q and the repsective R and C to achieve the filter requirement.
For a basic passive RLC bandpass filter, I am calculating the values of RLC for a specific resonance frequency and bandwidth. The resistor is 1 kilo-Ohm. For a bandwidth of 600 Hz, and a resonance frequency of 2kHz, what are the values of L and C given the following equations:Bandwidth = R/Lω0 = (1/LC)^(1/2)
Draw the circuit diagram of a first-order RC lowpass filter and give the expression for the half-power frequency in terms of the circuit components. Sketch the magnitude and phase of the transfer function versus frequency.
(a) Calculate fo, Q, and the bandwidth for the band-pass filter as shown if Rth = 1 kΩ, R2 = 200 kΩ, and C1 = C2 = 220 pF. (b) Use magnitude scaling to change the element values so that Rth = 3.3 kΩ. (c) Use frequency scaling todouble fo for the filter in part (a).
A transfer function is given by H( f )= 10 1−j( f/500 ) Sketch the asymptotic magnitude and phase Bode plots to scale. What is the value of the halfpower frequency?
H.W3 : a ) Design a narrow - band bandreject filter having a center frequency of 4 kHz and a quality factor of 10. Base the design on C = 0.5 uF . b ) Draw the circuit diagram of the filter and label all component values on the diagram . c ) What is the scaled transfer function of the filter ?
Consider the Sallen-Key low-pass filter circuit shown in Figure 2.Find the s-domain transfer function of the circuit in standard form.