The composite bar is stress-free before the axial loads P, and P2 are applied. Assuming that the walls are rigid, calculate the stress (MPa) in each material if P1 = 150 kN and P2 = 90 kN Aluminum A = 900 mm A = 2000 mm A = 1200 mm? E = 70 GPa | E = 200 GPa | E = 83 GPa Steel Bronze P 500 mm 250 mm 350 mm

The composite bar is stress-free before the axial loads P, and P2 are applied. Assuming that the walls are rigid, calculate the stress (MPa) in each material if P1 = 150 kN and P2 = 90 kN Aluminum A = 900 mm A = 2000 mm A = 1200 mm? E = 70 GPa | E = 200 GPa | E = 83 GPa Steel Bronze P 500 mm 250 mm 350 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 7CQ

See similar textbooks

Similar questions

The composite bar is initially stress-free. Calculate the stress in each material and indicate tension or compression if the temperature has increased to 25°C. Consider that the walls are unyielding and suitably braced to prevent buckling. Use 2 decimal places.
The modulus of elasticity of concrete (Force/Area) is 13 GN/m2. Determine its US Customary units (kip/in2).
Using a simply supported pre-stressed concrete beam, explain the following status using stress diagrams: Stress condition due to pre-stress alone. Change of stress conditions due to the increment of external load: Decompression moment (bottom fibre compression = 0); Cracking moment (tensile strength develops at the bottom and starts cracking at the bottom); and Balance state (whole section is at an equal amount of compression).
A beam, which is rectangular, has a base of 250 mm, and d = 575 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given b) Determine the value of "As"
fc = 25 mpa, fy = 414 the tensile stress is in the concrete is?
Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is ¾ X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is σ=20.0 ksi, the allowable shear stress for the rivets is σ=25.0 ksi and the allowable bearing stress on the rivets and splice plates is σ=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded?
A representative reinforced concrete composite beam section is shown in the figure below. The number of reinforcement is 6 and the diameter of the reinforcement is 16 meters. cross section Determine the neutral axis (x) and calculate the maximum normal stresses that will occur in concrete and steel. It will be assumed that the concrete does not carry tensile stress. The modulus of elasticity of the steel is 200000 Mpa. The modulus of elasticity of concrete is 28000 Mpa. The section width is b= 400 mm. Take the cover as 50 mm. (The maximum bending moment acting on the section is 59 kNm and d= 700 mm.)
The following data of a pre-stress concrete are given: Beam dimension ; bxh = 300 mm x 600 mm Loads Super imposed dead load 7 KN/m Live load = 20 KN/m Unit Weight of concrete 23 KN/cubic meter The beam is simply supported on a span of 15 meters and are pre tensioned with total initialpre tensioned with total initial force of 1750 KN from low-relaxation strand with centroid 220 mm below neutral axis throughout the beam length .There is a 15% loss of stress at service loads. The concrete covering of the pre-stressed concrete is _____mm., the total dead load is _____ KN/m.
Calculate the coordinates of the centroid, X'c and Y'c, for the composite section in figure, with respect to the x'Oy' coordinate system.
UPVOTE will be given! Please write the solutions completely and legiby. Box the final answer. Answer in 3 decimal places! Strength of Materials The assembly shown is made up of T-shape steel and two wood as shown. A bending moment M is applied to the composite beam. Given: Es = 200 GPa Ew = 25 GPa M = 90 kN.M h = 200 mm a. Calculate the distance of the centroid from the bottom of the beam in mm. b. Calculate the absolute maximum stress in the wood in MPa.
The composite bar shown in the figure is firmly attached to unyielding supports. An Axial force P = 52 kips is applied at 69∘F. Compute the stress (ksi) in the Aluminum at 118 ∘F. Assume α= 6.5 x 10-6/∘ F for steel and 12.8 x 10-6/∘F for aluminum Given: L1 = 17in; L2 = 11in Your final answer should contain two decimal places
Q: For a continuous and oriented fiber-reinforced composite, the moduli of elasticity in the longitudinal and transverse directions are 19.7 GPa and 3.66 GPa, respectively. A) If the volume fraction of fibers is 0.25, determine the moduli of elasticity of fiber and matrix phases. B) If the cross-sectional area is 200 mm? and a stress of 40 MPa is applied in this longitudinal direction, compute the magnitude of the load carried by each of the fiber and matrix phases. C) Determine the strain that is sustained by each phase when the stress in part (b) is applied.