The correct distance between points C and D is 213.5m. If a 100-m tape that is 0.025m too long is used to measure CD, what will be the measured distance in meters? (Give your answer in two decimal places)

The correct distance between points C and D is 213.5m. If a 100-m tape that is 0.025m too long is used to measure CD, what will be the measured distance in meters? (Give your answer in two decimal places)

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 42P

See similar textbooks

Related questions

Q: Find the value of the pull required to eliminate the effect of sag when the 50 m long tape weighing…

A: Given: Tape length, L=50 m Pull at the time of standardization, Po=10kg Weight of the tape = 0.03…

Q: show complete solution and formula What is the most probable value of a rectangular lot having the…

Q: In a laboratory, a flow experiment is performed over a hydraulic structure. The measured values of…

Q: A solid cube of side 1 m is kept at a room temperature of 32°C. The coefficient of linear thermal…

A: Given- side=1 m,α=1×10-5 /oC,k=200 GPa, It is needed to find the volumetric stress.

Q: The tension AB in the truss as shown in the figure below, is 100 N .Fill the following blanks: 2 m D…

Q: ies, and "Work" under the Construction Contract ent and contractor. Explain SIX (6) factors in sele

A: A construction contract is a written agreement between two parties that is mutually or legally…

Q: The reduction coefficient of a RC column with 4800 mm effective length and size 250 mm : 300 mm is…

A: given- RC column, effective length d=4800 mm, size- 250×300 mm,

Q: What is the equivalent constrained modulus in psf if the initial stress is 418 psf, the change in…

A: Given data:- The given initial stress, σ0=418 psf The given change in stress, ∆σ=1204 psf Maximum…

Q: Draw the shear and moment diagrams given that Ra=110.2 kN, Rb=310.1 kN, Rc=220.6 kN, Ma=-124.5 kN m,…

A: Solution: Bending moment and shear force diagram drawn as per moment distribution method. Span AB:…

Q: Derive an expression for the maximum value of deflection for the simlply supported beam.

Q: 1. A double-channel shape, 2C8 18.75, is used as a tension member. The channels are bolted to a…

A: The given figure is shown below:

Q: Compute the amount of concrete for the wall footing that will be built for the property that is…

A: Given: Thickness of footing = 8 in = 0.67 ft Width of footing = 4…

Q: The following subtended angles were read on a 2m long subtense bar using a theodolite. Compute for…

Q: The rectangular gate shown in Figure 2.65 is intended to control the flow of seawater into a…

A: Given : Density of freshwater = 998 kg/m3 density of seawater = 1025 kg/m3 weight of gate = 100lb/m…

Q: determine: a. Unit vector along line of action of vector P, ûp = b. Direction cosine angles…

Q: 6. A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular…

Q: Calculate the length of transition curve on a plain terrain and the shift using the fo Design speed…

A: Given V= 65kmphR= 220m1 in N = 1 in 150W+W_e= 7.5m

Q: 2.2m 550N/m

A: Given E= 15 Gpa I= 50 ×106 mm4

Q: During a series of tape measurements of a line, following values were determined: 887.57 m, 887.42…

A: Nothing is mentioned about the weights of measurements hence take the tape measurements are of equal…

Q: Wind blows on the side of the enclosed agriculture steel building located on open flat terrain. If…

Q: 四可

A: Given: a = 1.8 m b = 3 m t = 100 mm = 0.1 m LL = 24 kPa = 24 kN/m2 Reduction factor for live load:…

Q: Using double integration method determine the value of end shears, end moments and mid-span…

Q: A highway has on average a vehicle every 28 ft while queuing. What is the jam density in…

Q: Determine the projectile velocity and position 3 seconds after it is fired.

A: Given initial velocity u = 60 m/s Deceleration a = -0.4v3 m/s2 final velocity = v m/s At t = 3 sec…

Q: 5.2 For the calculation of net area of flat with staggered bolts, the area to be deducted from gross…

Q: 4. If viscous effects are neglected and the tank is large, determine the flowrate from the tank…

Q: In a laboratory, a flow experiment is performed over a hydraulic structure. The measured values of…

Q: Problem #3 Am D B -2 m- 2 m- -2 m BkN C KN Y KN Determine the force in each member of the truss.…

Q: oblem #3 Am -2 m B BkN 2 m- C KN -2m- Y KN

Q: A Portland Cement Concrete Pavement (Item 311) is t the following details: a. Length b. Concrete…

Q: A circular gate 1.2 m in diameter is inclined at an angle 30 deg. Sea water stands on one side of…

A: Given:Diameter of gate(D)=1.2 mAngle of inclination of gateθ=30°Specific gravity of sea…

Q: compound beam ABCDE shown determine the reactions at the supports A Show necessary Free body…

A: degree of static indeterminacy, Ds = number of unknown support reactions - number of equilibrium…

Q: The maximum number of vehicles observed in any five minute period during the peak hour is 160. If…

Q: A cyclone has a dpc of 5 µm, what is the overall removal efficiency for air stream that has the…

A: Given dpc = 5 µm

Q: Point 1-2 S. 7’’ 58’ W, 16.87m Lot-17 Point 2-3 N. 85’ 57’ W, 12.00m Road (6.0m wide) Point…

A: given data to plot given technical description LOT-16 Point 1-2 S. 7’’ 58’ W,…

Q: Reaction at support A and support B? Max moment in beam? Shear at point C?

Q: 3 6m ort at 4 can be assumed esumed A to be to B be a roller Point Ci

A: Please post other questions separately thank you CONSIDER AC

Q: 4. A 54 kg girl is walking up a 22kg uniform beam. The coefficient of friction is 0.2 at all…

Q: 2. What is the most probable value of a rectangular lot having the width and length of 239.01 ± 0.03…

Q: Is there any other way to got forces?

Q: The following subtended angles were read on a 2m long subtense bar using a theodolite. Compute for…

Q: 6. A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular…

A: Given Force P = 330 lb Required: (a) Determine the rectangular representation of Force Vector P.…

Q: Problem #4 Y KN G 30º 10 m X KN 60° 60% 10 m A KN 30 10 m D Determine the force in the members of…

Q: Determine the slope correction for steep slope and the horizontal distance AB if two lines AC and…

Q: An iron cannonball (specific gravity 7.87) floats in the mercury (specific gravity 13.56). What…

A: Answer : We are given Specific gravity of cannonball(SG)ball = 7.87 Specific gravity of…

Q: When an airport is designed, it is important to have the runways positioned so that planes take off…

A: The magnetic bearing or compass heading of the runway's centerline is known as the "runway…

Q: sand: Ydry = 14.6 kN/m³; Ysat = 17.3 kN/m³ clay Yeat 19.3 kN/m³; LL = 38% e = 0.75 If uniformly…

Q: Explain Multiroller

A: It is term related to geotechnical engineering.

Q: Find the value of the pull required to eliminate the effect of sag when the 50 m long tape weighing…

Q: 1. Investigate the adequacy of the beam loaded and supported as shown in accordance with AISC Specs.…

Concept explainers

Surveys of public lands

A survey is a method used to determine the relative positions of various objects on the land by measuring the horizontal distances between them. Briefly, a survey is a process of accumulation of data of various details related to land. The main objective of surveying land is to prepare maps to a suitable scale. Various types of maps such as topographical maps, cadastral maps, engineering maps, military maps, contour maps, geological maps, archaeological maps, and so on can be prepared by surveying.

Question

100%

Please help ASAP. Rate will be given accordingly. Write the answer on the paper.

The correct distance between points C and D is 213.5m. If a 100-m tape that is 0.025m too long is used to measure CD,
what will be the measured distance in meters? (Give your answer in two decimal places)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The measured distance between A and B is 505.71 m. If a 100 m tape that is 0.025 m too long is used to measure AB, what will be the correct distance in meters? a. 505.84 m b. 503.16 m c. 512.43 m d. 515.58 m
A 50-m tape was used to measure distance AB as 945.60m. The tape was discovered to be 50.075m after laboratory tests. a. What is the total correction (in meters)? b. What is the corrected length (in meters)?
The correct distance between two points is 130.35 m. Using a 100 m. tape that is 0.02 m. too long, what is the length to be laid on the ground? a. 120.345 m b. 130.376 m c. 130.324 m d. 130.122 m
A 50m tape was used to measure a line DE. The adjusted distance of line DE is 120.23m long. If the tape is 0.04m too short, what is the measured distance? Show complete solution Use 3 decimals
Fundamentals of Surveying: Please show your solution. 10 . A group of students were tasked to measure a certain distance. 3 students measured it as 3.352 m, 5 students measured it 3.307 m, and 7 students measured it as 3.397 m. What is the most probable value of the distance measured?
Solve the following problems showing your complete solutions. 1. A line 50 m long was paced by an engineer three times and recorded the following results: 58, 60, and 61. He also paced another line three times and again obtained the following results: 231, 236, and 227. Determine the length of the line. 2. The interior angles X, Y, and Z of a triangular traverse were measured with the same precision. The results were as follows: Station Interior Angles Number of Measurements X 410 3 Y 650 4 Z 750 2
A student was asked to make a 345.43 m long line using a 25 m tape that is 0.0021 too long, what is the required measurement?
Distance by Tachymetry 1. A stadia rod held at a distant point E is sighted by an instrument positioned at point D.Determine the length of line ED if the upper and lower stadia readings were observed as 1.50 and 1.40 respectively.
A 50m tape was used to measure a line DE. The adjusted distance of line DE is 120.23m long. If the tape is 0.04 too short, what is the measure distance?
A 100-meter tape weighing 5.08 kg was used to measure a line. It was supported at the end points, midpoint, and quarter points and the tension applied is 60 N. If the total measured distance is 2432.65 m, what is the correct distance of the line?
If the temperature and pressure at measurement time are 18°C and 760 mm Hg, respectively, what will be the error in electronic measurement of a line 3 km long if the temperature at the time of observing is recorded 10°C too high? Will the observed distance be too long or too short?
The correct distance between two point is 220.45m using a 100m tape that is x meter too long the length to be laid out on the ground should be 220.406m. What is the value of x?