Obtain an expression for the deflection curve of the simply supported beam of Fig. 8-7 subject to theuniformly distributed load w.WmmmmmFig. 8-7Determine the maximum deflection of above beam ifE=100GPa● W=200N/mL=4mRectangular beam section 2cmx8cm (W x D)In addition, you are asked to,W●Evaluate the types of connection that will be needed to provide the simply supported design●Discuss the relationship between bending shear, and deflection.• Evaluate steel and reinforced concrete and their structural efficiency in managing bending shear,and deflection.Answer All Questions.

Answered: Image /qna-images/answer/be8c850f-781b-4d11-91bf-60256aaa4c31.jpg

the deflection curve of the simply supported beam of Fig. 8-7 subject to the uniformly distributed load w W mmmmm Fig. 8-7 Determine the maximum deflection of above beam if E=100GPa W=200N/m L-4m Rectangular beam section 2cmx8cm (W x D)

the deflection curve of the simply supported beam of Fig. 8-7 subject to the uniformly distributed load w W mmmmm Fig. 8-7 Determine the maximum deflection of above beam if E=100GPa W=200N/m L-4m Rectangular beam section 2cmx8cm (W x D)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 3: M1 = 5.5 1) (2) 8₂ = 12° Air at Mach, M1 = 5.5 at a pressure of P1 = 70 kpa flows along a…

Q: Environmental Engine... ✓ The 500mL portions analysed using the membrane filter technique produce…

A: given- 500 mL portion samplecounts of coliforms per 100 mL-350, 370, 370 and 340

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 800 mm.…

Q: Visit the Web site of an engineering organization, such as ASME, IEEE, or ASCE, and prepare a…

A: According to the new finding, the utilization of oranges diminishes the gamble of diabetes. Thus,…

Q: Q1: For the problem in Figure (1), determine maximum allowable load P such that maximum flexural…

Q: rate Q and rotational spee that pND2/μ is a form of

A: SOLUTION OF ABOVE PROBLEM IS BELOW:

Q: Determine the value of EIō at C and value of the slope at A. Use conjugate beam method for this…

A: Given A simply supported beam Required Slope at A and EIΔ at C

Q: Irrigation Engineering The given data for the irrigation water is as follows: 1+ Na = 54 (meq/l)…

A: Given data- Concentration of-Na+=54 meq/LCa+=10 meq/LMg+=16 meq/LTo Find-The classification of water

Q: symmetrical parabolic curve passes through point a whose elevation is 23.27 m at a distance of 54 m…

Q: A massless beam has a loading pattern as shown in the figure. The beam is of rectangular cross…

Q: M = i R=( i kN.m i+ i j) KN

Q: 1- Consider the unit cube shown in the Figure, which undergoes the deformation: 1 x₁ =α (X₁- X₂), x₂…

Q: A horizontal collimation test is performed on an automatic level following the procedures described…

A: Answer We are given Instrument set up at point 1 rod reading at A (ha) = 3.886 ft rod reading at B…

Q: he jib crane is designed for a maximum capacity of 4 kN, and its uniform I-beam has a mass of 210…

A: (a) 1853.38 N (b) 1851.63 N (c) 1851.25 N at x=0.2 (d) 1855.47 N

Q: Explain how the functional characteristics and design selection criteria are informed by proposed…

A: FUNCTIONAL CHARACTERISTICS OF A PROPOSED BUILDING:- 1. STRENGTH The proposed building should be…

Q: Q/ The force in the member (CA) is 12m 50 ку 5m BX

Q: The A992 structural steel bar and a 2014-T6 aluminium bar shown below are secured to rigid supports…

A: Given :

Q: DEADLINE: JUNE 16, 2022 10:00AM) 30N Im 2m + + Im E = 200 GPG I= 5x10 mm 4 MOMENT-AREA METHOD No. 5…

Q: * Q2: The ladder in fig.(1), has a uniform weight of 100N and rests against the wall at B.If the…

Q: Q/ Compute the tension (T) in the cable? Neglect the friction between .the cable and the pulley 3 A…

A: Given,

Q: Compute the value of EIS at point B of the simply supported beam ABC using moment area method. 600…

A: Find EIδ Value at B using moment area method

Q: Find the value of EIS (N-m³) at the point of application of the 200 N-m couple in below: 500N 200…

Q: Solve for : sin - sec 0 + csc 0- tan 20= -0.0866 A. 40° B. 41° C. 47° D. 43°

A: As putting all the four values for θ and solving doesnot result in the given answer so all the four…

Q: A UNIFORMLY DISTRIBUTED FORCE OF Px=3 (COMPRESSION), Py=6 (TENSION) AND Pz=9 (COMPRESSION) IN THE X,…

A: Given data Px=3KN (COMPRESSION), Py=6KN (TENSION) AND Pz=9KN (COMPRESSION) IN THE X, Y AND Z…

Q: A 5m tall CLT Wall (Grade V1) is subjected to a dead load of 200 kN/m and a live load of 300 kN/m.…

A: Dead load on the wall = 200 KN/m live load on the wall = 300 KN/m Factored load = 1.2*200+1.6*300=…

Q: 4.7 A concrete beam of rectangular cross section of 200 mm x 400 mm is prestressed with a force 400…

Q: Q3) the state of plane stress at a point is represented by the element shown below. Determine state…

Q: The beam shown in Fig. is made from two boards. Draw the shear stress at (A.B.C.D) to hold the…

A: Reaction calculation For equilibrium of static (i)∑ME = 0 (ccw +ve, cw -ve) (RE x 8) - [6.5 x 4 x…

Q: Q2] Determine the value of W that may cause the pinned column AB with the pipe section shown to…

Q: OK, now we have to deal with the spoils. Assume the Finished Grade (FG) was level and all one…

A: Given Finished grade was level No slope Using minimum OSHA offset it is 2 Ft so…

Q: Question 1 * Each member of the truss shown is made of steel and has the cross-sectional area shown.…

Q: What is the sensitivity of a level vial with 2-mm divisions for (a) a radius of 40.4 m(b) a radius…

A: Sensitivity of level tube is given by ϕ=dR(206264.80'')d=2mm

Q: 03:Plot three of the following. 1) Typical structures of a loess soil.

A: As per company policy, we are supposed to answer only the first question of the multiple question…

Q: 8 mm and the ho material fr

Q: The following is the set of observed data for successive 15 minutes period of 105 minutes storm in a…

Q: Four forces are exerted on the eyebolt as shown. If the net effect on the bolt is a direct pull of…

A: Given: The resultant force is 590 lb about the y-axis. The value of F1 is 370 lb. The value of F2 is…

Q: A horizontal reducing bend deflected at 110° has a diameter of 250mm upstream and 100mm downstream.…

A: Given Specific Gravity of fluid= 0.90

Q: A simply supported beam has a span of 12 m. The beam carries a total uniformly distributed load of…

A: Given, Uniformly distributed load, w = 21.5 kN/m = 21.5 N/mm Length of the beam, L = 12 m = 12000…

Q: Two tangents AB and BC meet in an inaccessible point B and are to be connected by a simple curve of…

Q: does depend on?

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: 4.7 A concrete beam of rectangular cross section of 200 mm x 400 mm is prestressed with a force 400…

Q: A 17.0 m high and 11.0 m long wall and it bracing under construction are shown in the figure.…

A: wind load intensity w = 670 N/ mm2 area of wall = 17 x 11 = 187 m2 number of braces n = 10

Q: power P required t iscosity u, impeller

Q: Draw the shear and moment diagram for the beam with the loads and supports. PLACE ALL YOUR PROCEDURE…

Q: Compute the value of El 6 at midspan for the beam loaded as shown in Fig. P-611. It E= 10 GPa, what…

Q: Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.7 GPa. Bar (2) is a nylon…

Q: Example 14.5: A cable having span of 100 m, dip "h" = 10 m is subjected to a rise is temp. of 10°C.…

Q: (1) The out-plane stability formula of beam-columns recommended in the design code is as following:…

A: The values of these factors are as follows:

Q: Problem 2.1 The Grashof number, Gr is defined as: (where g is gravitational acceleration, B is…

A: Grashof number is used to differentiate the flow type as below

Q: The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Obtain an expression for the deflection curve of the simply supported beam of Fig. 8-7 subject to the
uniformly distributed load w.
W
mmmmm
Fig. 8-7
Determine the maximum deflection of above beam if
E=100GPa
● W=200N/m
L=4m
Rectangular beam section 2cmx8cm (W x D)
In addition, you are asked to,
W
●
Evaluate the types of connection that will be needed to provide the simply supported design
●
Discuss the relationship between bending shear, and deflection.
• Evaluate steel and reinforced concrete and their structural efficiency in managing bending shear,
and deflection.
Answer All Questions.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the slope and deflection atB and E of the beam and loadings shown using area moment method. The section of the beam is tubular with outer diameter of 500mm and inner diameter of 200mm. Take E=20GPa.
(a) Compute the horizontal deflection at D and the vertical deflection at F by the virtual work method. (b) If members GF, BI and CF are 3mm longer, 2mm longer and 1mm shorter, compute the horizontal deflection at G? Given E=200GPa and A=103mm2 .
For the beam shown below, determine the slopeand deflection at D. Use conjugate-beam method. E=12 GPaand the beam is made of wood 75 mm by 150 mm. Neglect theweight of beam.
The cantilever beam is a 10 in length carbon steel bar, with a diameter of 1 in. And it is charged by a force F = 100 lbf.A) A Find the maximum deflection using the method of virtual forces, including that resulting from shear.B) What error will be introduced if the shear is disregarded?
Determine the internal moments at the supports of the beam shown using: 1.) ThreeMoment equation 2.) Moment Distribution Method 3.) Slope-Deflection Method Pick two method only Given: E=200GPa I=20x10^6 mm^4 w=8kN/m L1=10m L2=8m
A 6m simply supported beam AB carries 2 concentrated downward loads of P=26KN each placed at third points of the beam span. With constant EI=21000 KN-m2. Using Double Integration Method (DIM) with origin taken at point A (left support) where 0 ≤ x ≤ 6m, calculate the maximum deflection of the beam? Express your answer in "mm" in 2 decimal places. Include (-) negative sign if deflection is downward.
A beam 4m long is simply supported at its ends. The beam is loaded with a downward vertical load 300N at a point 1m from the left support. Using E = 180 GPa, I = 160 x 106 mm⁴. Determine the following using the double integration method a) The rotation (in degrees) of the beam at the left support b) The deflection of the beam at midspan c) The maximum deflection
Q) Determine the equation of the elastic curve for the beam shown below using continuity equations. Find the deflection at point B. EI is constant. F . | 4/e B el am 6m am
Compute the value of the following for the beam shown: (EI is constant.). Using moment area methoda) Slope θAb) Slope θBc) Slope θCd) Deflection ΔCe) Maximum deflection between support
Compute the maximum deflection of the W10 x 39 cantilever beam shown? Neglect the weight of the beam. Assume E = 29 xl0^6 psi and Ix = 209 in^4.
Using Macaulay’s Method calculate the required second moment of area (I) for the steel beam shown in the image attached given that Young’s Modulus is 200 kN/mm2 and the central deflection of the beam may not exceed span over 360.
Calculate the value of the deflection at point B due to uniformly distributed load w in the form answer in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.