Please show a your work when sliding this physical applications question to help me better understand. Thank you The Deligne Dam on the Cayley River is built so that the wall facing the water is shaped like the regionabove the curve y = 0.1² and below the line y = 280. (Here, distances are measured in meters.) Thewater level is 24 meters below the top of the dam. Find the force (in Newtons) exerted on the dam bykgmwater pressure. (Water has a density of 1000-and the acceleration of gravity is 9.8- (:)$₁2sec²m³

Answered: Image /qna-images/answer/839928c0-2dee-4b95-b1c9-782209a139f0.jpg

The Deligne Dam on the Cayley River is built so that the wall facing the water is shaped like the region above the curve y = 0.12² and below the line y = 280. (Here, distances are measured in meters.) The water level is 24 meters below the top of the dam. Find-the force (in Newtons) exerted on the dam by kg water pressure. (Water has a density of 1000- m sec² m³ and the acceleration of gravity is 9.8- A.

The Deligne Dam on the Cayley River is built so that the wall facing the water is shaped like the region above the curve y = 0.12² and below the line y = 280. (Here, distances are measured in meters.) The water level is 24 meters below the top of the dam. Find-the force (in Newtons) exerted on the dam by kg water pressure. (Water has a density of 1000- m sec² m³ and the acceleration of gravity is 9.8- A.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.113P: Calculate the resultant force caused by the water acting on the parabolic arch dam. The water levels...

See similar textbooks

Similar questions

The three reservoirs system contains water. If L1 = 2000 m, f 1= 0.013, D1 = 1m; L2 = 2300 m, f2 = 0.02, D2 = 0.60m; and L3 = 2500 m, f = 0.023, D3 = 1.20m. Compute Q3 in m3/s.
A gate rotates at point A and releases water when the water's depth, d, exceeds a certain value. The gate's width (perpendicular to the image) is b = 2.95 ft, the water's depth is d = 4.82 ft, and point A is located at h = 2.41 ft. a) What is F, the magnitude of the horizontal force exerted on the gate by the water? The water's specific weight is γw=62.4lb/ft3. b) What are Ax and Bx, the horizontal reaction forces at points A and B that act on the gate from Part A. c) What is dmax, the water's maximum depth before the pressure causes the gate from part A to open?
Find the surface tension of the water droplet of 30 mm diameter when the inside pressure is 3.5 N/m2 The surface tension in N/m is
Answer is: V = 14.17 ft/s
The tank of water in Fig. is 12 cm wide into the paper.If the tank is accelerated to the right in rigid-body motion at6.0 m/s 2 , compute ( a ) the water depth on side AB and ( b ) thewater-pressure force on panel AB . Assume no spilling.
The face of a dam is a vertical rectangle of height 100 ft and width 200 ft (Figure 6.8.5a). Find the total fluid force exerted on the face when the water surface is level with the top of the dam.
Find the horizontal pressure acting at the face of the damn at 20ft depth.
plzzzzzzz help What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
The discharge of water through a pipe of diameter 40 cm is 400 litres/s. If the pipe is bend by 135", find the magnitude and direction of the resultant force on the bend. The pressure of flowing water is 29.43 N/cm²
An open vessel of water accelerates up to a 30ᵒ plane at 2 m/s². a). What is the angle the water surface makes with the horizontal? B). If the angle mage by the water surface to the horizontal is increased to 25.21ᵒ, what will be the depth of water at the rear side of the vessel, if the initial depth of water at the rear side is 4m and the front is 2m before accelerating? The vessel has a length of 4m and 2m width. C). If the vessel’s depth at the rear side is 5m, what will be the volume spilled if the acceleration is increased to 15m/s²?
Water flows in a channel with uniform curvature ?. The channel has height ℎ = 5 mm and width ? = 190 mm (normal to the drawing plane). The curved part of the channel has a length of ? = 100 mm in the ?-direction. You can assume that the channel height is very small compared to the curvature radius.Neglect effects of gravity. a) Assuming that the pressure is uniform on each of the channel walls, determine the pressure difference between the upper and lower wall that is needed if the required net force on the two walls is 2000 N pointing downward (in the negative ?-direction).Use a sign convention that a positive pressure difference or gradient means the pressure at the higher ?-position is higher. b) Your team agree that, from experience, the average velocity of the fluid is ?= 53 m/s. Assuming that the velocity is uniform across the channel, and neglecting gravitational effects, determine the curvature ?required to generate this force with this flow velocity. Use a sign convention that…
The distance between the two plates, which are 2 m x 2 m in size and parallel to the earth surface, is 9 mm, and there is water at 20 ° C between them. Find the force in (N) to be applied to pull the top plate to the right at 10 m / s.