I need the answer as soon as possible The discharge in m/s for laminar flow through apipe of diameter 0.04 m having a centre linevelocity of 1.5 m/s is

Given data; ac. to question;The discharge in m3/s for a laminar flow…

Answered: The discharge in m3/s for laminar flow

Engineering

Mechanical Engineering

The discharge in m3/s for laminar flow

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.4P: 5.4 Evaluate the Stanton number for flow over a tube from the following data: , , , , .

See similar textbooks

Related questions

Q: Convert: 15 ft/s^2 to m/min^2

Q: S.57. Compute the discharge over the spillway when the head on the spll

A: Head on the spillway, h1=10 m,Height of the spillway, H=60 m,Spillway discharge coefficienct, kr=0.5…

Q: 9.25. Compute the discharge from the tank shown in Fig. 9.42. Air, 2 psi 3 in, diam Oil, sp gr 0.92…

A: Given: air pressure, P1=2 Psi or 13789.5 Pascal jet diameter, d=3 inch or 0.0762 m height, h= 4 ft…

Q: Convert a flow of water flowing in a pipe 370 Liters/ hr into kg/hr, _m³/min discharge in kg/hr…

Q: QUESTION 02 Consider a single acting triplex pump having 7-in. liners and 12-in. stroke length…

Q: A standard short tube, 4 in. in diameter, discharges water under a head of 20 ft. What is the…

A: Discharge: The volume of the fluid that is flowing through a particular cross-sectional area is…

Q: regular exit 90" elbow 20 n Sharp entrance Half-open gate valve 12-in bend radius Pump Onen elobe

A: Solution :- Given data :- ρ = 2 slugs/ft3 = 1030.76 kg/m3ν= 0.000012 ft2/sec = 1.1148×10-6 m2/secQ =…

Q: Enumerate the different classifications of pumps

A: There are mainly two types of pump : 1. Dynamic pumps 2. Positive displacement pump 1. Dynamic…

Q: What hp must be supplied to pump 2 cu. ft per sec from the lower to upper reservoir if the pump…

A: Flow rate, Q=2 ft3/secPump efficiency, η=75%Roughness of the pipe, e=0.003 ftElevation at lower…

Q: Water is supplied at a rate of 3000 litres per minute from a height of 4 metres to a hydraulic ram…

Q: Explain three pages about laminar flow

Q: Determination of Discharge Thru a Siphon

A: Given Height = 83.5 cm To find Theoretical discharge Actual discharge Difference percentage

Q: Oil is flowing upward through a Venturi meter as shown. Assuming discharge coefficient is 0.984,…

A: Given:- Upward flow in venturi meter Discharge coefficient, C=0.9284 d1=500mm d2=200mm The specific…

Q: Flow of water from a pipe connected to a tank is 10 m/s. Determine the height of the tank.

Q: * In series-pipe problems the discharge through each pipe is added to obtain total discharge

Q: Determine the TDH for the system shown below taking into account that the discharge in

A: Given:

Q: Q6. A dru of (1m) is one end of other end i drum. Hov the siphon tube of fric

A: GivenD=0.6mz1=1mz2=-0.5md=15mmL=3.5mf'=4f=0.001cc=0.55

Q: The effect of introducing orifice plate in the flow meter is

Q: Determine the pump head (unit: meter or kPa), using the following parameters

Q: Discuss the flow through the Coarse and soft pip.

A: Coarse Pipe- In coarse pipe, the surface irregularities are more which destroyed the laminar…

Q: Convert a flow of water flowing in a pipe 340 Liters/ hr into _m³/min kg/hr, discharge in kg/hr…

Q: The water in an aquarium will be drained for cleaning. A flexible tube (D = 4mm) will be used to…

A: The volumetric flowrate of water is 2.587 LPM (litre/min).

Q: Required: Pump efficiency

A: efficiency = power delivered by pump / power input to pump

Q: Write relation of dynamic head with co-efficient of discharge.

Q: estimate the volume flow rate of water through the siphon

A: Given data: Apply Bernoulli’s equation between the free surface of the tank and the exit of the…

Q: Convert a flow of water flowing in a pipe 350 Liters/ hr into. kg/hr,. m3/min discharge in kg/hr

A: 1lit/hr=0.74kg/hr =0.74*350=259kg/hr

Q: Drive an expression for the loss in laminar flow.

Q: i. The flow capacity of the fan in litres/min ii. What the height of the residential building should…

A: We are to get the lpm of duct flow then determine the height of building

Q: Write relation of flow rate with total head in bernoulli's equation

A: The flow rate is equal to amount of fluid flowing through a cross section in unit time. The formula…

Q: Calculate the discharge throug

A: To find Discharge

Q: IS flowin pipe at average velocity 6f m/S. Assun TIOW IS laminar, calculate the kinetic energy…

A: Kinetic energy correction factor = Kinetic energy per second based on actual velocityKinetic energy…

Q: Determine the pump head required to pump water between the two ta figure. Water flowrate is 5.6x103…

Q: The maximum flow rate is 4437.02 O barrels per day.

A: To find Maximum flow rate

Q: For flow nate 28 Lis rale Sind pump Power

Q: 1. Design a system to pump water at 140°F from a sump below a heat exchanger to the top of a cooling…

Q: What is the time is taken by the system to fill a tank of capacity 315 liters and flow rate 25 x…

A: Given data tank of capacity (v) = 315 liters = 0.315 m3 flow rate = 25 x 10 3 m³ per hour = 6.944…

Q: 10.86 An air-conditioning system is designed to have a duct with a rectangular cross section 1 ft by…

A: Given Data For the same pressure drop along the pipe ∆hrect=∆htrap (hf)rect=(hf)trap Hydraulic…

Q: Write relation of elevation with dynamic head.

Q: Pumps are rated by its maximum O a. pressure,speed and flow. O b. output flow and spee in rpm O C.…

A: Pumps are rated so that the standardization of the performance of the pump can be done on the basis…

Q: in fully developed laminar flow (1-4r2/D²), whereris the radi

Q: What is the hydraulic radius of a circular pipe that is half full with water?

A: Given that a circular pipe is half full of water, Let r be the radius of pipe.

Q: 3- Discuss the flow through the Coarse and soft pip.

A: Given Rough pipe Soft pipe To find Flow pattern through rough and soft pipe

Q: e flow type

A: Flow is laminar.

Q: n efficiency óf 72%. Thé surface of e friction pressure drop in the pipe

Q: Calculate the following: 1.Head at the discharge side,m 2. Velocity Head, m 3. Total Head of the…

Q: Determine the total discharge in

A: NEED TO FIND TOTAL DISCHARGE.

Q: Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: When the two pumps are connected in series, their resultant pump performance curve is given by…

Question

I need the answer as soon as possible

The discharge in m/s for laminar flow through a
pipe of diameter 0.04 m having a centre line
velocity of 1.5 m/s is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The velocity of flow of water at the centre of tube is _______ when the head is 0.1m, η=8.9*10-3 dynes-s/cm2, γw=1 g/cm3, the length is 10m and the diameter is 20cm.Dont attempt wrong I will dislike
A 230-m-long pipeline delivers 20◦C water to a storage reservoir located downstream. The pipeline is galva-nized with an average roughness height of 0.2 mm. An axial pump is used to pressurize upstream water. Thewater surface in the reservoir is located 18 m above the centerline of the pump. The pump discharges waterat an absolute pressure of 400 kPa and a volume flow rate of 50 L/s. Calculate a diameter of pipe requiredto achieve such an operating condition. If needed, use the Moody diagram on the last page, or one can solvethe Colebrook equation using, for example, Matlab.
Water at 20 ° C flows steadily through the piping junction inFig. P3.32, entering section 1 at 20 gal/min. The averagevelocity at section 2 is 2.5 m/s. A portion of the flow isdiverted through the showerhead, which contains 100 holesof 1-mm diameter. Assuming uniform shower flow, estimatethe exit velocity from the showerhead jets.
a pumping station working with a pump head of 25m. the output power of the motor for that pump is 16kw. identify the pump efficiency if the sewarge discharge velocity is 0.27 m/s and the pipe diameter is 250 mm
Comment on the significance of any experimental errors for ORIFICE AND FREE JET FLOW
A pipe of 0.25 m diameter carries water at the rate of 7.2 m3/s.The pressure head at the entry of the venturimeter, used to measure the flow rate in the pipe, is equivalent to 6 m of water. If the pressure head at the throat is zero, calculate the throat diameter of the venturi.Include fbd.
HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.
In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation30 over a hill of elevation 50. A pump of what power is required to maintain a pressure of 345kPa on the hilltop if the head lost between reservoir and hilltop is 6 m?
It is proposed to run the pump at 880 r/minto pump water at 20°C through the system in Fig. .The pipe is 20-cm-diameter commercial steel. Whatflow rate in ft3/min will result? Is this an efficientapplication?
46. Consider the case of an ideal fluid flow in the conduit of Problem 19. Findpressure at the exit of the conduit in terms of the flow density and velocities at theinlet and the outlet.
Is it easier to solve for the head loss when it's a laminar flow than turbulent flow?
A semi-spherical tank of radius R is completely filled with water. Now a hole of cross-sectional area Ah and discharge coefficient Cd at the bottom of the tank is fully opened and water starts to flow out. Develop an expression for the time needed to empty the tank completely.