Figure3 ft5 ftB< 1 of 1> The door is made from one piece, whose ends movealong the horizontal and vertical tracks. Assume the dooris a 180-1b thin plate having a width of 10 ft. (Figure 1)Figure< 1 of 1>Part AIf the door is in the open position, 0 = 0°, and then released, determine its angular velocity at the instant = 28 °, measuredcounterclockwise.Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise andnegative value if the angular velocity is clockwise.1977| ΑΣΦ= لهاSubmitRequest Answer< Return to Assignmentvec 1Provide FeedbackReview?rad/s

To Find: the angular velocity.Given:the instant the weight of the door is the width is

The door is made from one piece, whose ends move along the horizontal and vertical tracks. Assume the door is a 180-1b thin plate having a width of 10 ft. (Eigure 1) ▼ Part A If the door is in the open position, 0 = 0°, and then released, determine its angular velocity at the instant 0 = 28°, measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. Η ΑΣΦΙΚΗ1 | vec = لها Submit Request Answer < Return to Assignment Provide Feedback Review ? rad/s

The door is made from one piece, whose ends move along the horizontal and vertical tracks. Assume the door is a 180-1b thin plate having a width of 10 ft. (Eigure 1) ▼ Part A If the door is in the open position, 0 = 0°, and then released, determine its angular velocity at the instant 0 = 28°, measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. Η ΑΣΦΙΚΗ1 | vec = لها Submit Request Answer < Return to Assignment Provide Feedback Review ? rad/s

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.73P

See similar textbooks

Similar questions

Given the image below, AB and BC are joined by a hinge in b. End A of member ASB is pin supported while end C is constrained to move along horizonal surface. What is the velocity at C if Member AB rotates clockwise at a constate rate of 3rad/s?
The triangular plate is fixed at its base, and A is given a horizontal displacement of Δs′= 4 mm. Suppose that L=800 mm.
A flywheel has a rim weight of 480 kg and mean radius of 480 mm. If the rim width is 6 times the rim thickness and material density is 7300 kg/m^3, calculate for the width of the flywheel. Answer = 361.7 mm
Determine the angular velocity, in rpm, of the rotating drum which results in loss of contact between the clothes and the drum at 1.0239 rad. Assume that the small vanes prevent slipping until loss of contact. Round your answer to 2 decimal places
a rotating shaft carries four unbalanced masses 18 kg, 14 kg, 16 kg and 12 kg at radii 50 mm, 60 mm, 70 mm and 60 mm respectively. the 2nd, 3rd and 4th masses revolve in planes 80 mm, 160 mm and 280 mm respectively measured from the plane of the first mass and are angularly located at 60°, 135° and 270° respectively measured clockwise from the first mass looking from this mass end of the shaft. the shaft is dynamically balanced by two masses, both located at 50 mm radii and revolving in planes mid-way between those of 1st and 2nd masses and midway between those of 3rd and 4th masses. determine, graphically or otherwise, the magnitudes of the masses and their respective angular positions.
The triangular plate is fixed at its base, and its apex A is given a horizontal displacement of 5 mm. Suppose that a= 640 mm
Solve the force and its direction with Fx=130N, Fy=115N
Given the image below, AB and BC are joined by a hinge in b. End A of member ASB is pin supported while end C is constrained to move along horizonal surface. What is the speed of point B if Member AB rotates clockwise at a constate rate of 3rad/s?
Referring to Prob. 18.143, (a) prove that the Poinsot ellipsoid is tangent to the invariable plane, (b) show that the motion of the rigid body must be such that the Poinsot ellipsoid appears to roll on the invariable plane. [Hint: In part a, show that the normal to the Poinsot ellipsoid at the tip of w is parallel to HO. It is recalled that the direction of the normal to a surface of equation F (x,y,z), ) = constant at a point is the same as that of grad F at point P.J
Two spur wheels with involute teeth gear together externally. The pitch circle diameters are 120 mm and 300 mm and the smaller wheel has 19 teeth. The pressure angle is 20o and the addendum is 0,3 of the circular pitch. Determine 1.1 The length of the arc of approach if the smaller wheel is the driver, and 1.2 The maximum velocity of sliding between the teeth when the driver rotates at 200 r/min
A spacecraft must be maneuvered through an angle of 6O-deg in 30 s. The spacecraft moment of inertia is 8000 kg-m^2; the thrusters are located at a radius of 2.2 m from the center of mass. What is the minimum thrust level for the thrusters? Answer : 1.90 N. Don't give me wrong answers. correct answer is 1.90....show me how
The turning-moment diagram for an engine consists of two isosceles triangles each with a height equivalent to a torque of 16kNm. The bases of the triangles lie between ? = 0 ? and ? = 180? , and ? = 180? and ? = 360? Sketch the turning-moment diagram and add the mean torque line. If the engine is to rotate with a mean speed of 130 rpm, calculate the following: the power developed the mass of the flywheel having a radius of gyration 1.1m to restrict the fluctuation of speed to +1.5% of the mean speed. Demonstrate which would be most effective to reduce the fluctuation of speed, a change in diameter of or a change in mass of the flywheel.