The electric motor keeps the aluminum shaft ABCD, with rigidity modulus 27 GPa, operating at a constant speed when torques TB=240 N.m and Tc=390 N.m are respectively exerted at B and C. If the diameter of the shafts are given as dAB= 40 mm, dBc = 50 mm, and dcp=50 mm, determine (a) Angle of twist of A relative to B (b) Angle of twist of C relative to B (c) Angle of twist of C relative to D The magnitude of the internal reaction torque between A and B is The magnitude of the internal reaction torque between B and C is The magnitude of the internal reaction torque between C and D is (N.m) (N.m) (N.m)

The electric motor keeps the aluminum shaft ABCD, with rigidity modulus 27 GPa, operating at a constant speed when torques TB=240 N.m and Tc=390 N.m are respectively exerted at B and C. If the diameter of the shafts are given as dAB= 40 mm, dBc = 50 mm, and dcp=50 mm, determine (a) Angle of twist of A relative to B (b) Angle of twist of C relative to B (c) Angle of twist of C relative to D The magnitude of the internal reaction torque between A and B is The magnitude of the internal reaction torque between B and C is The magnitude of the internal reaction torque between C and D is (N.m) (N.m) (N.m)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
e g O single cylinder reciprocating engine has speed 240 rp.m., stroke 3 mm, mass of reciprocating parts 50 kg, mass of revolving parts at 150 mm radius 37 kg, I MUO third of the reciprocating parts and all the revolving parts are to be balanced, find : 1. The bala,:A mass required at a radius of 400 mm, and 2. The residual unbalanced force when the crapg h; rotated 60° from inner dead centre. T e T g LSOt ULy A PO Eangt
B 2 ~s A single cylinder reciprocating engine has speed 240 rp.m., stroke 3 mm, mass of re ocating parts 50 kg, mass of revolving parts at 150 mm radius 37 kg. UMOO third of the reciprocating parts and all the revolving parts are to be balanced, find : 1. The bala,;: mass required at a radius of 400 mm, and 2. The residual unbalanced force when the crank g rotated 60° from inner dead centre. P e AN R eR e e g
A vertical shaft 25 mm diameter and 0.75 m long is mounted in long bearings and carries a pulleyof mass 10 kg midway between the bearings. The centre of pulley is 0.5 mm from the axis of theshaft. Find (a) the whirling speed, and (b) the bending stress in the shaft, when it is rotating at 1700r.p.m. Neglect the mass of the shaft and E = 200 GN/m2.
In the case of circular shaft subjected to pure torsion nonzero are: (a)Nx (b)Nx and Vy (C)Mz and Vy (D)Nx and My (E)My andVz (F)Mx
A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof 32 Hz. The gears at B and C take out 120 kW and180 kW, respectively. The lengths of the two parts ofthe shaft are L1 = 1.5 m and L2 = 0.9 m.Determine the required diameter d of the shaft ifthe allowable shear stress is 50 MPa, the allowableangle of twist between points A and C is 4.0°, andG = 75 GPa.
The shaft shown below consists of three segments AB, BC and CD is subjected to the three torques T1=114 N.m, T2=245 N.m and T3=441 N N.m. The length of each segment is L1=0.71 m, L2=0.31 m and L3=0.43 m . The diameter of each segment is d1=46 mm, d2=97 mm and d3=131 mm . The material have modulus of rigidity G = 143 Gpa. Answer the following questions
A solid shaft 100 mm diameter transmits 100.6 horsepower with a maximum allowable shear stress 25 MN/m ^2 . What is the spced of rotation of the shaft in (r.p.m)? (b) If the solid shaft is replaced by the hollow shafl transmitting 100 kW at the same rotation speed of the solid shaft. The hollow shaft has a mean torque =5/6 of maximum torque with the angle of twist 0.35° per meter length of the shafl and G= 80 GN/m^2 Determine the dimensions ofr the hollow shaft if the internal diameter of the shaft is to be 80 % of the external diameter.
Q3/ A vertical double acting steam engine develops 80 kW at 240 rpm. The maximum fluctuation of energy is 25% of the work done per stroke. The maximum and minimum speeds are not to vary more than +1% of the mean speed. Find the mass of the flywheel, if the radius of gyration is 0.65 m.
Q2: A solid steel shaft A of 60 mm diameter rotates at 300 rev/min. Find the greatest power that can be transmitted for a limiting shearing stress of 60 MN/m2 in the steel. It is proposed to replace A by a hollow shaft B, of the Same external diameter but with a limiting shearing stress of 75 MN/m2 . Determine the internal diameter of B to transmit the same power at the same speed.