The equivalent impedance per phase of a star-connected load are as follows: Za= 100 Ohms, Zb=j5 Ohms, Zc= -j5 Ohms. If the load is connected to a 440 V supply, phase sequence an-bn-cn. Total power of the load." (THIS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE A LETTER BELOW AND PROVIDE YOUR CLEAR SOLUTION!) A 880 VA lag B 645.3333 VA C 717 VA D 880 VA lead

The equivalent impedance per phase of a star-connected load are as follows: Za= 100 Ohms, Zb=j5 Ohms, Zc= -j5 Ohms. If the load is connected to a 440 V supply, phase sequence an-bn-cn. Total power of the load." (THIS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE A LETTER BELOW AND PROVIDE YOUR CLEAR SOLUTION!) A 880 VA lag B 645.3333 VA C 717 VA D 880 VA lead

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.45P: Two balanced Y-connected loads, one drawing 10 kW at 0.8 power factor lagging and the other IS kW at...

See similar textbooks

Similar questions

1. The equivalent impedance per phase of a star-connected load are as follows: Za= 100 Ohms, Zb=j5 Ohms, Zc= -j5 Ohms. If the load is connected to a 440 V supply, phase sequence an-bn-cn. a. Total power factor of the load.b. Total power of the loadc. Calculate Ia,Ib, Ic
Solve all parts or will dislike For the following circuit, the source voltage phasor is: ?s = 250.7∠ -4.16 deg ? a) Calculate the equivalent workshop impedanceb) Deduce the value of the phasor ?c) Calculate the voltage at the workshop terminals using the ohm lawd) Calculate the voltage at the workshop terminals using the law of loopse) Determine the real and reactive powers of the workshop and its power factor solve all parts or will dislike
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, and admittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. Please show complete solution and draw the circuit diagram. Please round off answers up to the 3rd decimal place.Thank you!
An acb sequence balanced three-phase Y-connected source supplies power to a balanced, three-phase Δ-connected load with an impedance of 15 + 6i Ω/ϕ. The source voltage in the b-phase is 240∠−45∘ V. The line impedance is 1 + 1i Ω/ϕ. Use the single phase equivalent circuit for the a-phase to find the current in ampere in the a-phase of the load. Express your answer using polar notation, only provide the polar angle in degrees.
A balanced 3-phase load of 23.5 MVA with PF=0.85 lagging is supplied with a balanced 3-phase source of 12.5 kV (line-to-line). Determine: VLL, IL, and VLN, The phase angle between phase voltage and current, θ, S3ϕ, S3ϕ, P3ϕ, and Q3ϕ, ZY if load is wye and ZΔ if load is delta, What size capacitor bank (in kVAR) would need to be installed to increase the PF to 0.9 lagging.
"A three phase motor is connected to a balanced three-phase supply. Meters placed in the circuit obtained the folllowing data: 400 V line-line voltage, 9 A line current, and 5 KW total power. Assume delta connection for the equivalent circuit of the load. What is the phase voltage of the motor?" (THIS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE A LETTER BELOW AND PROVIDE YOUR CLEAR SOLUTION!) A 400 V B 692 V C 231 V D 800 V (THIS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE A LETTER BELOW AND PROVIDE YOUR CLEAR SOLUTION!)
Three Impedances each of (11 – j20)Ω are connected in mesh across a three-phase 410V ac supply. Determine the phase current, line current, active power, reactive power drawn from the supply. Also, draw the Phasor diagram for the mesh connection and mark the Line current, phase current line voltage, and phase angle between phase current and phase voltage. phase current (Ip) = Line current = real power= reactive power=
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
1. Three impedances Z1, Z2 and Z3 are delta-connected to a symmetrical 3-phase, 400 V supply of phase sequence RYB. Z1 = (8 – j 6) Ω and is connected between lines R and Y. Z2 = (6 + j 8) Ω and is connected between lines Y and B. Z3 = (10 + j 0) Ω and is connected between lines B and R. Calculate (i) line and phase currents (ii) power per phase (iii) total power. Verify the results by creating a MATLAB Simulink model and program. Obtain the plots for the currents and voltages. Repeat for a case when the same loads are now connected in star.
This wind farm needs a 250 km connection laid to Sommerville. The choice is either a 3 phase system or a bipolar dc system at 400 kV and ±400 kV at the receiving end respectively. (i) The 3-phase system has resistive losses per phase of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (ii) The bipolar dc system has resistive losses of 0.1 Ω/km. Calculate the system losses (in watts) when delivering 0.8 GW. (iii) Calculate the efficiencies of the two systems. (iv) Comment on which system you would choose to use and why.
A balanced three-phase star-connected R-C load of 145 kW takes a current of 54 A with a line voltage of 900 V, 50 Hz. Find the circuit constants of the load per phase. Impedance, Power factor , Resistance
An acb sequence balanced three-phase Y-connected source supplies power to a balanced, three-phase Δ-connected load with an impedance of 15 + 6i Ω/ϕ. The source voltage in the b-phase is 240∠−45∘ V. The line impedance is 1 + 1i Ω/ϕ. Use the single phase equivalent circuit for the a-phase to find the current in ampere in the a-phase of the load. Express your answer using polar notation, only provide the polar magnitude.