The extruded plastic shape has dimensions of D = 31 mm, d = 25 mm, a = 93 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 375 N. (b) If the allowable shear stress for the plastic material is 1550 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion

The extruded plastic shape has dimensions of D = 31 mm, d = 25 mm, a = 93 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 375 N. (b) If the allowable shear stress for the plastic material is 1550 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Vertical Stress Increase In Soil

Section: Chapter Questions

Problem 8.7P: A 9 ft wide and infinitely long flexible strip load of 800 lb/ft2 is placed on an elastic medium as...

See similar textbooks

Similar questions

Refer to Figure 8.27. The flexible area is uniformly loaded. Given: q = 300 kN/m2. Determine the vertical stress increase at point A located at depth 3 m below point A (shown in the plan). FIG. 8.27
A 9 ft wide and infinitely long flexible strip load of 800 lb/ft2 is placed on an elastic medium as shown in Figure P8.7. Find the vertical stress increase at points A, B, and C located 3 ft below the surface.
The extruded plastic shape will be subjected to an internal shear force of V = 280 lb. Dimensions of the cross section are b = 1.1 in., d = 2.2 in., c = 1.5 in., and t = 0.20 in. Determine:(a) the magnitude of the horizontal shear stress at points A and B.(b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 0.8 in. below the z centroidal axis.(c) the magnitude of the maximum horizontal shear stress in the extrusion.
The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of the cross section are b = 2.0 in., D = 4.0 in., C = 2.7 in., And t = 0.19 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 1.4 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion
According to the elastic theory, the vertical stress induced by a point load of magnitude Q on the surface of a semi-infinite soil mass can be estimated by the expression. A point load Q=1500 kN is applied at the ground surface. Evaluate the stress in the soil caused by the point load at a depth of 2.5m directly below the load in kPa. Evaluate the stress at a depth of 2.5m and a horizontal distance of 3m from the point load.
An axial load of 100 kN is applied to a flat bar 20 mm thick, tapering in width from 120 mm to 40mm in a length of 11 m.Assuming E=200GPa, Determine the total elongation of the bar.
Two horizontal plates are parallel to one another and separated by an oil film (SAE 10 oil at 20 deg C, Table A.4) that is 1.0 mm thick. The upper plate moves to the right at 2.0 m/s. The bottom plate moves to the right at 6.0 m/s. What is the shear stress in N/m2 of the oil on the upper plate? Is the shear stress on the upper plate directed to the right or to the left?
A closed cylindrical tank, placed horizontally, 400 mm in internal diameter and 2.2 mm thick is subjected to an axial compressive force (along its longitudinal axis) and uniform internal pressure. The stresses acting on an element of side is shown in the figure. a. What is the magnitude of the internal pressure in MPa?b. What is the applied axial force in kN?c. What is the maximum shear stress in MPa?
The velocity profile of a viscous liquid flowing over a fixed plate is given by v=0.68yy2(v is the velocity in m/s and y is the distance from the plate in m).i. Calculate the shear stresses at the plate surface and 0.34 m away from the plate(µ=0.9 Ns/m2).ii. Draw the velocity and the shear stress profile of the system.
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a solid circular bar. a) Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b) If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c) Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
Develop the shear stress distribution , volumetric flow rate, average velocity and point of maximum velocity for u =U
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.