The extruded plastic shape will be subjected to an internal shear force of V= 395 lb. Dimensions of the cross section are b = 1.2 in., d = 2.4 in., c = 1.6 in., and t = 0.16 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 0.8 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion. (Гуp.) A YC Answer: (a) TA = i psi TB = psi (b) TC = psi (c) Tmax = i psi

The extruded plastic shape will be subjected to an internal shear force of V= 395 lb. Dimensions of the cross section are b = 1.2 in., d = 2.4 in., c = 1.6 in., and t = 0.16 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yc = 0.8 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion. (Гуp.) A YC Answer: (a) TA = i psi TB = psi (b) TC = psi (c) Tmax = i psi

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.1CTP: EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on...

See similar textbooks

Similar questions

The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of the cross section are b = 2.0 in., d = 4.0 in., c = 2.7 in., and t = 0.19 in. Determine:(a) the magnitude of the horizontal shear stress at points A and B.(b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 1.4 in. below the z centroidal axis.(c) the magnitude of the maximum horizontal shear stress in the extrusion
The extruded plastic shape will be subjected to an internal shear force of V = 350 lb. Dimensions of the cross section are b = 2.0 in., D = 4.0 in., C = 2.7 in., And t = 0.19 in. Determine: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the horizontal shear stress at point C, which is located at a distance of yC = 1.4 in. below the z centroidal axis. (c) the magnitude of the maximum horizontal shear stress in the extrusion
From the given figure below and its properties, calculate the stress at the top where at the fixed end. (MPa) Properties: Beam width = 274 mmBeam height = 419 mmWLL = 8.86 kN/mWDL = 12.6 kN/mPu = 7 kNSpan of the beam = 8 mPrestressing force = 399 kNeccentricity = 127 mm
The major and minor principal stresses acting at a point are 50 Pa compression and 10 Pa compression, respectively. Draw the Mohr’s circle for this stress combination, and determine the magnitude of shear and normal stress on one of the planes where shear is a maximum.
A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load).
Two horizontal plates are parallel to one another and separated by an oil film (SAE 10 oil at 20 deg C, Table A.4) that is 1.0 mm thick. The upper plate moves to the right at 2.0 m/s. The bottom plate moves to the right at 6.0 m/s. What is the shear stress in N/m2 of the oil on the upper plate? Is the shear stress on the upper plate directed to the right or to the left?
Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m2due to application of line loads q1 and q2. Determine the magnitude of q2.
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
Determine the magnitude of the maximum in-plane shear stress at point A (in MPa).
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 52 MPa, Sy = 63 MPa, and Sxy = 29 MPa.(a) Determine the principal stresses and the maximum in-plane shear stress acting at the point.(b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)(c) Compute the absolute shear stress at the point.
A propped cantilever beam of length ? = 1 m, with an inner hinge at point B, carries a uniformly distributed load ?, as shown in Figure Q1 (a). The beam is made from a circular hollow section with an inner radius of ?? = 5 cm and a thickness of ? = 2 cm (refer to Figure Q1 (b)). The maximum allowable longitudinal stress of the beam is 150 N/mm2.
Consider member (1). Use the yield stress, the factor of safety, and the force to calculate the minimum cross-sectional area required for member(1). A1= ? (unit mm^2)