The figure above on the left side shows the first quadrant of the J-V and power curves of an ideal and a non- ideal solar cell. The black dashed lines indicate the maximum power point of each cell. On the right side, figures (a) and (b) show the equivalent circuits of an ideal and a non-ideal solar cell respectively. To answer the following questions, estimate values from the graphs as accurately as possible, since small deviations in readings could lead to large deviations in the results. A) From the figure, estimate the Fill Factor of the ideal cell. Give the answer in [%] with one decimal place. B) Likewise, estimate the Fill Factor of the non-ideal cell. Give the answer in [%] with one decimal place.

The figure above on the left side shows the first quadrant of the J-V and power curves of an ideal and a non- ideal solar cell. The black dashed lines indicate the maximum power point of each cell. On the right side, figures (a) and (b) show the equivalent circuits of an ideal and a non-ideal solar cell respectively. To answer the following questions, estimate values from the graphs as accurately as possible, since small deviations in readings could lead to large deviations in the results. A) From the figure, estimate the Fill Factor of the ideal cell. Give the answer in [%] with one decimal place. B) Likewise, estimate the Fill Factor of the non-ideal cell. Give the answer in [%] with one decimal place.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.22P: The real power delivered by a source to two impedances, Z1=4+j5 and Z2=10 connected in parallel, is...

See similar textbooks

Similar questions

Write the differential equation for t > 0 for iC in the given figure. Assume VS = 9 V, RS = 4 kohm, R1 = 11 kohm, and R2 = R3 = 20 kohm.
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). a) Suppose that between the two terminals of an element there is a voltage v (t) and that a current i (t) enters through the terminal marked with a positive sign. Show that if v (t) and i (t) are sinusoidal and are out of phase by an angle ϕ, then the active power P that is consumed by said element is proportional to cos ϕ. b) How much is P for a pure inductor and how much for a pure capacitor? Does this make physical sense? c) When specifying the power factor seen between two terminals, why is it necessary to indicate whether it is lagging or leading? d) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. Then repeat the procedure but for two elements in series. e) What meaning would you give to the P consumed…
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). a) Suppose that between the two terminals of an element there is a voltage v (t) and that a current i (t) enters through the terminal marked with a positive sign. Show that if v (t) and i (t) are sinusoidal and are out of phase by an angle ϕ, then the active power P that is consumed by said element is proportional to cos ϕ b) How much is P for a pure inductor and how much for a pure capacitor? Does this make physical sense? c) When specifying the power factor seen between two terminals, why is it necessary to indicate whether it is lagging or leading?
A)Calculate V1 and v2 for t > 0, if the circuit is in steady stateat t = 0-. B)Calculate i for t > 0, if ig = 10 A and the circuit is in steady statepermanent at t = 0-.
Two pure elements, R = 30 ohms and C = 400 microfarad, in a parallel connection have an applied voltage of the form v = 200 cos (2000t - 30degree) volts. Find the value of the total current at time t = 52 milliseconds.
In the circuit given in the figure, Rk = 1.48Kohm, R1 = 7964.99Kohm, R2 = 7035.01Kohm, R3 = 2.46Kohm, R4 = 0.82Kohm, R5 = 24.08ohm, Ry = 98.63Kohm, VCC = 15.00V, VTN = 2.45V, Kn = Since 3.28(mA/V^2), C1= 6.30uF, C2=14.98uF, C3=10.96uF, calculate the lower cutoff frequency of the circuit in Hz.
In the circuit given in the figure, Rk = 1.48Kohm, R1 = 7964.99Kohm, R2 = 7035.01Kohm, R3 = 2.46Kohm, R4 = 0.82Kohm, R5 = 24.08ohm, Ry = 98.63Kohm, VCC = 15.00V, VTN = 2.45V, Kn = Since 3.28(mA/V^2), C1= 6.30uF, C2=14.98uF, C3=10.96uF, calculate the lower cutoff frequency of the circuit in Hz. When making your transactions, 2 digits will be taken after the dot.
To attain maximum power delivered to a load, what value of load impedance is required if a. the load can have any complex value; b. the load must be pure resistance?
Electrical Engineering _ Energy Conversion Systems pls findthe question by using computer line. pls find fast.
A field party in Antarctica is using a tent that has been equipped with a small outdoor gasoline generator. The generator’s Thevenin equivalent circuit has V T of 120 V DC and the equivalent resistance, R T , of 10 Ω. There are two resistive heaters inside the tent: R 1 = 10 Ω and R 2 = 120 Ω , that can be connected to the generator separately, in series, or in parallel. For the highest heater power output, how should the heaters be connected to the generator?
Please solve step by step subject power system analysis
Answer the following points in detail and rigorously. Instead of resorting to formulas, develop from basic principles (laws of voltages and currents, definition of electrical power, properties of phasors, among others). a) Show that the complex power consumed by two elements in parallel is the sum of the individual complex powers. Then repeat the procedure but for two elements in series. b What meaning would you give to the P consumed by an element? Which to Q? c) Suppose you know P and Q for a two-terminal element. What is the power factor of this element? When would you be ahead and when would you be behind? d) Suppose you know the equivalent resistance R and the equivalent reactance X of a two-terminal passive network. What is the power factor of this network? When would you be ahead and when would you be behind?