The figure displays a three-phase delta-connected motor load which is connected to a line voltage of 440 V and draws 4 kVA at a power factor of 72 percent lagging. In addition,a single 1.8 KVAR capacitor is connected between lines a and b, while a 800-W lighting load is connected between line c and neutral. Assuming the abc sequeñče ănd takingVan = Vo, 0°, find the magnitude and phase angle of currents la, Ip, Ic, and In.a oI,1.8 KVARboMotor loadсоI,4 kVA,dopf = 72%, laggingSingle phase, 800 W lighting load connected tophase C only. Pf for lighting loads is unity.800 W lighting loadADegrees. Wne your answer in numeral form without units, rounded off to two(2) decimal places.Ib =ADegrees. Write your answer in numeral form without units, rounded off to two(2) decimal places.ADegrees. Write your answer in numeral form without units, rounded off to one(1) decimal places.In =ADegrees. Write your answer in numeral form without units without decimal places.

The figure displays a three-phase delta-connected motor load which is connected to a line voltage of 440 V and draws 4 kVA at a power factor of 72 percent lagging. In addition, a single 1.8 KVAR capacitor is connected between lines a and b, while a 800-W lighting load is connected between line c and neutral. Assuming the abc sequenče ånd taking Van = Vp/ 00, find the magnitude and phase angle of currents /a, Ip. la, and In. I ао I, 1.8 KVAR bo Motor load I, 4 kVA, do pf = 72%, lagging Single phase, S00 W lighting load connected to phase C only. Pf for lighting loads is unity. 800 W lighting load 2 = | A Degrees. Write your answer in numeral form without units, rounded off to two(2) decimal places. A Degrees. Write your answer in numeral form without units, rounded off to two(2) decimal places. I = A Degrees. Write your answer in numeral form without units, rounded off to one(1) decimal places.

The figure displays a three-phase delta-connected motor load which is connected to a line voltage of 440 V and draws 4 kVA at a power factor of 72 percent lagging. In addition, a single 1.8 KVAR capacitor is connected between lines a and b, while a 800-W lighting load is connected between line c and neutral. Assuming the abc sequenče ånd taking Van = Vp/ 00, find the magnitude and phase angle of currents /a, Ip. la, and In. I ао I, 1.8 KVAR bo Motor load I, 4 kVA, do pf = 72%, lagging Single phase, S00 W lighting load connected to phase C only. Pf for lighting loads is unity. 800 W lighting load 2 = | A Degrees. Write your answer in numeral form without units, rounded off to two(2) decimal places. A Degrees. Write your answer in numeral form without units, rounded off to two(2) decimal places. I = A Degrees. Write your answer in numeral form without units, rounded off to one(1) decimal places.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.44P: Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a...

See similar textbooks

Similar questions

Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4j2.7) per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging, and the other 132 kW at unity power factor. The line-to-line voltage at the load end of the line is 2203V. Compute (a) the line-to-line voltage at the source end of the line. (b) the total real and reactive power losses in the three-phase line, and (c) the total three-phase real and reactive power supplied at the sending end of the line. Check that the total three-phase complex power delivered by the source equals the total three-phase comp lex power absorbed by the line and loads.
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.
S.4) the length of a three-phase power transmission line with a Nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/km. From the end of the line, a 56 MW star connected load is fed with a power coefficient of 0.8 back under a 64 kV interphase voltage. If the line head voltage of the transmission line is 69 kV, calculate the capacity and power of the star-connected capacitor to be shunted into the load connected to the end of the line.
Q5. A single phase overhead transmission line has a supply voltage of 34 kV and a sending end current of magnitude 40 A at 0-8 p.f. lagging is feeding a certain load. The total resistance and inductance of the line are 5 and 21 mH respectively. Draw the practical circuit used and the devices necessary to perform this experiment. Then calculate the sending end power, receiving end current, voltage, power factor, receiving end power and line efficiency Vs 34000 Is 40 Cosos 0.8 R 5 Ps Ir Vr Cosor Pr n 21e-3
A single phase distributor 1 km long supplies a load of 100A at 0.8 p.f. lagging at its far end and a load of 200A at unity p.f. at its mid-point. Both power factors are referred to the voltage at the far end. The resistance and reactance per km (go and return) are 0.1 Ω and 0.2Ω respectively. If the voltage at the far end is maintained at 200V, calculate feeder current, voltage at the sending end . Also find phase angle between voltages at mid-point and sending end.
A short 3-phase transmission line connected to a 33kV, 50 Hz generating station at the sending end is required to supply a load of 10 MW at 0·8 lagging power factor at 30 kV at the receiving end. If the minimum transmission efficiency is to be limited to 96%, estimate the per phase value of resistance and inductance of the line. [2·4 Ω; 0·028 H]
A 3-phase, 50 Hz, overhead transmission line delivers 10 MW at 0·8 p.f. lagging and at 66 The resistance and inductive reactance of the line per phase are 10 W and 20 W respectively while capacitance admittance is 4 × 10- 4 siemen. Calculate : (i)the sending end current (ii) sending end voltage (line-to-line) (iii) sending end power factor (iv) transmission efficiency Use nominal T method.
A 3-phase, 50 Hz overhead transmission line, 100 km long, 110 kV between the lines at the receiving end has the following constants : Resistance per km per phase = 0·153 W Inductance per km per phase = 1·21 mH Capacitance per km per phase = 0·00958 µF The line supplies a load of 20,000 kW at 0·9 power factor lagging. Calculate using nominal p representation, the sending end voltage, current, power factor, regulation, and the efficiency of the line. Neglect leakage.
A 3-phase, 60 Hz, 55 km long overhead line supplies 575 kW at 11 kV, 0.9 p.f. lagging. The line resistance is 3.5 Ω per phase and line inductance is 10 mH per phase. Calculate the Reactance of the Line, Current flowing through the transmission line, Sending end voltage, Voltage regulation and Efficiency of transmission. Inductive Reactance= Current flowing through the transmission line= Sending end Voltage=
Exercise 1: A three-phase 3Φ transmission line has an impedance of 0.62+j35.06Ω/phase and supplies a three-phase load of 100MW with a power factor (fp) of 0.8 lagging at 200kV. Taking 100MVA and 215kV as a base, we ask: a-) Calculate the impedance of the line in p.u;b-) Calculate the current consumed by the load in p.u;c-) Calculate the load voltage in p.u; PLEASE, TYPE, HAND WRITING GETS UNDERSTANDING.
A 3-phase, 50 Hz, 30 km long overhead line supplies 525 kW at 11 kV, 0.8 p.f. lagging. The line resistance is 5 Ω per phase and line inductance is 15 mH per phase. Calculate the Reactance of the Line, Current flowing through the transmission line, Sending end voltage, Voltage regulation and Efficiency of transmission. Inductive Reactance: Current flowing through the transmission line: Sending end Voltage: Voltage Regulation of Transmission line: Transmission line efficiency:
A 50 Hz, 250 V single phase power line has the following loads placed across it in paralell; 4 kW at a pf of 0. 8 lagging; 6 kVA at a pf of 0.6 lagging; 5 kVA which includes 1.2 kVAR leading. Determine the overall pf of the system and the capacitance of the capacitor which, if connected across the mains restore the power factor to unity.