Answered: The flow in a river is 2500O L/s per 2…

Engineering

Civil Engineering

The flow in a river is 2500O L/s per 2 m width and the silt factor is 1.2. The Lacey's scour depth (in m) is

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter2: Geotechnical Properties Of Soil

Section: Chapter Questions

Problem 2.11P

See similar textbooks

Related questions

Q: In the triangle ABC segment DE is parallel to that of AC. Determine the length of AC when AD=7,…

A: Given- Triangle ABC-DE is parallel to ACAD=7DB=2DE=3

Q: رشت تا فياين( Fur the beam shown, a. draw sFD and BMD, b. prove that for the isosceles:, max. = bh…

A: Given : Support Reaction : ∑MD = 0 ⇒ RB×6 - 40 - 2×3×32+6 - 12×3×3×33+6 = 0…

Q: Find the elastic strain when total yield strain is 0.005in/in.

Q: Assuming the pavement condition and cross section remain constant. The terrain is also constant…

A: e + f = V2/(225R) ; here e = 0.07{max super elevation} , f = 0.15{lateral friction}, R = radius of…

Q: The drawing shows a rectangular block of glass (n = 1.52) surrounded by a liquid with n = 1.79. A…

Q: Discuss experience Unconfined dompressive Strength of Cohesive Soil

Q: - In 1:40 model of 9 spillway, the velocity and discharge are 2 m/s and 2.5 m/s. Find the…

Q: 6. Discussion: 1. Is there a difference between the values of Qideal calculated by equation (1) and…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: Example 3 A new building is constructed near an old building, as shown in figure. For both buildings…

A: Given data- Uniform pressure at base of footing-q=22 t/m2=22×9.80=215.6 kN/m21 ton=9.80 kNYoung…

Q: -µg/L of NaOH should be added in water to change the pH from 7 to 9 at 25°C.

Q: group of 9 driven piles, 12 m long and 300 mm in diameter is to be arranged in a square pattern in…

Q: Solve 5,6

A: 5. The orientation of shallow knockout failure will always be in the direction of radial/axial…

Q: The maximum diameter that a capillary tube can have to ensure that a capillary rise of atleast 6 mm…

A: given-capillary rise h=6 mmsurface tension T=0.08 N/mdensity ρ=900 kg/m3

Q: A 25-mgd water treatment plant has a flocculation tank 64 ft long and 100 ft wide with a water depth…

Q: forensic photography.

A: Forensic photography includes methods of photographing the scenes of crimes, searches, investigatory…

Q: The ionic character of a groundwater is defined by the following hypothetical combinations:…

A: Given data- concentrations-Ca(HCO3)2=3.0 meq/LMg(HCO3)2=0.4 meq/LMgSO4=0.8 meq/LNa2SO4=0.2…

Q: A FLOCCULATION BASIN IS DESIGNED TO TREAT 20000 M3/DAY OF WATER WITH DETENTION TIME OF 150 MINUTES.…

Q: Question 3 Discuss the process of levelling benchmark. The discussion should cover the levelling…

A: Explanation- The art of calculating the elevation of one level in relation to another is known as…

Q: a. How far is the vertical resultant force from the toe? b. What is the factor of safety against…

A: Question has five subparts, here only three suparts have been solved.

Q: The scale of the photography taken from a height of 300 m, with a camera of focal length 15 cm, is O…

A: Given data : Height of photography =300 m Focal length = 15 cm

Q: Calculate Maximum Deflection for B2 Use E = 25 GPa Cross Section of B2 = 200x350 mm DL = 15.978 kN/m…

Q: possible to have two civil engineers with the same training, experience, capabilities, and…

A: According to my perspective,it may not possible to have two civil engineers with the same training,…

Q: A car moves with initial velocity of 2 m/s and it is accelerating at rate of 4 m/s2. Find the final…

A: Given data : The value of initial velocity of car U=2 m/s The value of acceleration a=4 m/s2 The…

Q: 400 Kgim B -6 m 10 m 45"

Q: il flow at 230 l/s through 200 mm diam riction factor 0.0224. ind head loss

A: Oil flow ( Q ) = 230 L/sec Diameter ( d ) = 200 mm Length of pipe L = 500 m Friction factor f =…

Q: How do the back of the house menu design and customer profiles influence a production kitchen…

A: The designing of the structure is now a days become very complex process. To solve this different…

Q: Examine the reasons why HetNets are particularly well suited for use in urban settings

A: HetNets generally refers to heterogenous network: The need for data traffic as well as coverage…

Q: rigure Q3 shows the cross section of an existing road in a flat rural area. a) Briefly explain the…

Q: Determine the critical net area for the given connection if 18mm diameter bolts were used. Plate…

A: In diamond rivetting rivets are arranged in a diamond pattern and decrase gradually from inner row…

Q: Draw Bending moment diagram of Uniformly Distributed cantilever beam supported at A.

A: Uniformly Distributed cantilever beam. To find: Bending Moment diagram Cantilever beam is the…

Q: Steel frame (dead lo2 klf (Serua Wa and Wind live 24 Kif (Service) a kif= Ww 0ltimate H =10 ft 32 ft…

Q: A strip footing is needed to carry a load of 100 kN/m at a depth of 1 m. Shear strength parameters…

Q: 554. What safe value of W can be applied to the beam loaded as shown in Fig. P-554 if o, < 60 MPa…

A: step 1-

Q: Determine the pressure difference (in kPa and answer should be a whole number) between the water…

Q: Problem 1: Draw the bending moment diagram and calculate 0 at B using slope- deflection equations. A…

Q: Select the TRUE response. With increasing flow rate the frtiction factor of a given pipe decreases…

Q: 6 KN Fo the beam shown, draw SFDand BMD. Ans. Rg -19.5KN, RC= 10.5 KN. 15 KN.m 17KN, m SKNIM 2m 2m 2…

Q: Oil flow at 230 1/s through 200 mm diameter pipe 500 m long. Friction factor 0.0224. Find head loss

A: Given data : Length of pipe L=500 m Diameter of pipe d=200 mm Friction factor f=0.0224 Discharge…

Q: 554. What safe value of W can be applied to the beam loaded as shown in Fig. P-554 if o, < 60 MPa…

Q: Q31. A trapezoidal channel with bottom width of 4.0 m and side slopes 1:1 has Manning's N of 0.02.…

Q: A tensile test was conducted on reinforcement steel bar having a diameter of 10 mm to record the…

A: For the given data of stress and strain, the stress vs strain curve has to be plotted. Also, the…

Q: Compute the radius of relative stiffness of 20 cm thick cement concrete slab from the following…

Q: Topic: Shear and Moment Diagram Solve 5 problems (following the conditions stated below) involving…

A: Only fifth problem is done as asked.

Q: 19-5. Develop a signal timing for the intersection shown below. 30 ft N PHF = 0.92 Level terrain…

A: Given Data PHF=0.92Target v/c ratio =0.95Average approach speed =30 mi/h (N-S)Average approach…

Q: In the beam shown in the given figure, for all positions of load W (except x =0) Find maximum…

Q: Discuss the latest technology in levelling surveying (other than automatic level) that can be used…

A: Levelling can be done with different types of instruments. Some are done with the help of automatic…

Q: Compute the radius of relative stiffness of 20 cm thick cement concrete slab from the following…

A: Relative stiffness The relative stiffness is the stiffness value when compared to another material…

Q: A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8…

Q: A common bar suspended has an axial load of 1000 lb, it has a cross sectional area of 20 sq. in.…

A: Given data : The value of axial load P=1000 lb The value of cross sectional area A=20 in2 Required…

Q: A four-lane rural freeway segment has a 510 m grade length of 2% upgrade followed by a 630 m grade…

A: No of lane in both direction = 4

Question

The flow in a river is 2500O L/s per 2
m width and the silt factor is 1.2. The
Lacey's scour depth (in m) is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

PROBLEM. 3 A rectangular cross-section stream has a depth of h = 3 m, cross-section area of 200 m², and a discharge of 100 m³/s with bottom slope of 0.0001. The density and kinematic viscosity of water in the stream are p = 999.1 kg/m³and v= 1.14×106 m²/s. The bed sediment material is of quartz sand and the sieve diameters are d35= 0.25 mm and das = 0.5 mm. The specific gravity of the quartz sediment particles is 2.65. The stream has bed forms (note that in the solution of the problem if you like you can also make use of the Vanoni-Brooks diagram). Find the total shear stress at the bed of the stream.
A confined aquifer is 6 m thick and the coefficient of permeability in the soil is 2m/day-m2. Two wells tapped on the aquifer are 100 m apart, and the difference in the water elevation in the wells is 3.0 m. The effective porosity is 0.38. What are the average (Darcy) velocity through the aquifer and the flow rate per meter width of aquifer? Darcy velocity is 0.06 m/day and the flow rate is 0.36 cubic meter per day per meter width. Darcy velocity is 0.16 m/day and the flow rate is 0.06 cubic meter per day per meter width. Darcy velocity is 0.16 m/day and the flow rate is 0.36 cubic meter per day per meter width. Darcy velocity is 0.06 m/day and the flow rate is 0.16 cubic meter per day per meter width. The best answer is not among the choices.
A confined aquifer shown has hydraulic conductivity of 52 m/day with void ratio of 0.282. The average thickness is 30 m and the average width is 4 km. el = 85 m el = 55 m 80 m aqulfer 1400 m Determine the nearest value of the tirne of travel from the head of aquifer to a point 5.2 km downstream in days (in a whole day).
be the hydraulic conductivity at 20 Docs A20 pe 4. For a normally consolidated clay, the following values are given. k (cm/sec) 0.45 x 106 0.78 1.1 0.88 x 106 Estimate k at a void ratio of 0.97
A vertical sand column of length 100 cm and cross section area of 150 cm² is allowing the water to flow downward. The head difference was found to be 110 cm. The soil has a hydraulic conductivity of 20 mld and void ratio was taken as 0.5. Calculate the (a) rate of flow, (b) the Darcy velocity and (c) the average velocity.
If the hydraulic conductivity of a sand at a void ratio of o.6 is o.03 cm/s, its value at the void ratio of o.75 will be O a. 0.03 O b. 0.05 O C. 0.07 O d. none of the above Hide Feedback Incorrect
Assume a=2d, and plot the dimensionless concentration profiles C/C, for sediments with 0.016 mm, 0.125 mm, 0.5 mm in a 3 m deep very wide channel with slope of S=0.002.
be the hydraulic conductivity at 20°C? Ans. 1.0 x 10 cm/sec 4. For a normally consolidated clay, the following values are given. k(cm/sec) 0.45 x 10 e 0.78 1.1 0.88 x 10 Estimate k at a void ratio of 0.97 6.0089 107
Lacey's scour depth for a stream carrying a discharge of 3 cumecs metre width and having a silt factor of 1.2 is m. S A 26.40 B 2.64 d C 0.264 D 12.64 K
Lacey's scour depth for a stream carrying a discharge of 3 cumecs per meter width having a silt factor 1.2 is
An anisotropic soil deposit has coefficient of permeability in vertical and horizontal directions as k, and k, respectively. For constructing a flow net, the horizontal dimension of the problem's geometry is transformed by a multiplying factor of kx kz (a) (b) Kz Kx kz (c) k, (d)
The hydraulic conductivity of a sand at a void ratio of 0.62 is0.03 cm/sec. Estimate its hydraulic conductivity at a void ratioof 0.48.