The following is the bearing and length measurements of an opentraverse A) Determine the latitude and departure of the lines B) What is the distance from the starting point of A to the last point of F Line length 100m BEARING N 30deg30'E N45 degE S 60 degE S 85 deg W N 40 degE line AB BC 200m CD 250m DE 75m EF 140m

The following is the bearing and length measurements of an opentraverse A) Determine the latitude and departure of the lines B) What is the distance from the starting point of A to the last point of F Line length 100m BEARING N 30deg30'E N45 degE S 60 degE S 85 deg W N 40 degE line AB BC 200m CD 250m DE 75m EF 140m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

C 5.8 m 3.2 m 1 hi 12 3,5 m %3D h2 4.5 m h2 L203X152X25.4 Shape Steel A992 Gr. 50 Gage of Angles 75 mm g1 T 75 mm g2 Bolt h 28 mm Bolt Diameter, dbolt 50 mm A aspace 65 mm b,pace d. 90 mm Сэрасе 70 mm 12 dapace 90 mm espace 95 mm fapace I || |||
Q2. Find Iep -30 50 В 20 A 40 R=20 +-20 - y 20 40 Ix
Typing f Facebc (1) Me M Fwd: F E Sta X E Statics G detern G teremi S HW11 nt/d/1DJXbp051_Aq9VmLFLk-ukINmQzs-MT107ZoOyL3D4Ng/edit 100% Normal text Calibri 11 BI 3 4. 6 kipe 10 ft B. Determine the forces in members FH, DH,EG and BE in the truss using the 3kips 10 ft D. kups t ft method of sections. 1 ft 15 it
Which feature control frame would you use to tolerance the one-inch slot perpendicular to datum feature A and symmetrical with the four-inch feature within a tolerance of .005 at MMC in the drawing below? Use MMC and MMB wherever possible. 1.000-1.010 138 4.000-4.020 A. B. C. D. E. O E O O A с B B OD .005(M) A 4.00 .005 MA BM 1 005 (M) A BM 0.005MABM .005 M AMB 2.00 A
Ở (MPa) 80 60 40 20 0. 0. 0.002 0.004 0.006 0.008 0.01 0.012 Figure 3 CS Scanned with CamScanner
Please can u give it to me accurate ans for this one thanks dear eng
PROBLEM 01 REFER TO FIGURE 01, DETERMINE THE INTERNAL FORCES ACTING ON THE FOLLOWING MEMBERS: (STATE COMPRESSION OR TENSION) o FG o FC GH CH
Gate ACB is in a shape of a sector of a circle whose radius is 6m as shown. Determine the following: a) Horizontal component FH is Blank 1 KN b) Vertical component Fv is Blank 2 KN c) Distance of FH from point "C" is Blank 3 m c) Distance of Fv from point "C" is Blank 4 m
Q3- Calculate 500kN A + 2.5 + 4 + 3m 4 + 4m kD=25mm ke 66 D=35mm D=45mm Z=20x10 AVA-? 1
gs9a7d6fg 87bas5b6 t87sa6 78ysadf87y 78asdgfh87wawhtw
What part of the connection shown does not comply with NSCP 2015 Section 510.3.3, 510.3.4 and 510.3.5? PL290x8mm M22 Bolts 40 75 75 40 40 75 120 O Center to center spacing of 120mm O Edge distance of 40mm O Longitudinal center to center spacing of 75mm O Transverse center to center spacing of 75mm
Help me pls, i give you upvote :)