The following program is supposed to add the contents of memory location 2050H to the accumulator. The program works correctly Only part of time. Show what is wrong with the program and how to correct it. MOV B,A Save accumulator contents in B. LDA 2050H Get second operand. ADC B Add them together. RST 1 Stop

The following program is supposed to add the contents of memory location 2050H to the accumulator. The program works correctly Only part of time. Show what is wrong with the program and how to correct it. MOV B,A Save accumulator contents in B. LDA 2050H Get second operand. ADC B Add them together. RST 1 Stop

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter3: Static Electricity

Section: Chapter Questions

Problem 10RQ: What special property does this material have that makes it useful in a copy machine?

See similar textbooks

Similar questions

You buy a ROM chip that is 2Kx8. How many memory address lines does the chip have? A. 2K B. 16K C. 11 D. 8
You buy a ROM chip that is 2Kx8. How many memory address lines does the chip have? 2K 16K 11 8
The top picture is the schematic block and the one below it is the circuit diagram inside of the schematic block The whole nand gates circuit diagram should be inside of the schematic block wasn't it? Task 1 solve above follow instructions
design a two-way traffic light system with prototype using 4-bit down counter circuit. use 7-segment as an output to represent the timer.i need help.. pls make a circuit diagram for this. (like circuit wizard and tinkercad) i will do this on the breadboarduse simple ic only like dual jk flip flopsthank you.. sorry for asking again.
a. If the disruptive input is zero, is the system stable (do your operations as Gb(s)= 1)?b. What should Gb(s) be so that the disruptor input B(s) has no effect on the system output?
Here are 4 EEPROM memory system. What addresses are associated with each of the 4 memory chips. I think I got a couple of them but I'm not sure I'm doing this right. Could you show me how you would go about this? Thank you for your help.
Identify the contents of the registers, the memory location (C055H), and the flags as the following instructions are executed in 8085 microprocessor. A H L S Z CY M(C055H) LXIH, C055H MVI M,8AH MVI A,76H ADD M STA C055H HLT
7- Write an 8051 program to exchange the contents of the stack pointer SP and the flag register PSW.
You buy a ROM memory chip that is 64Kx8. How many memory address lines does the chip have? A 16 B 64K C 512 D 8
Which one of the following instructions will cause a memory read when it is executed? MOV BL, AL MOV BL, 0203 MOV AL , BL MOV AL, [0203] OR MOV [0203], AL
a.Write the addressing modes of the following instructions: (i) MOV A, @R0(ii) MOVX @DPTR, A (iii) MOVC A, @A+DPTR (iv) MOV R0, #45H b) Write instructions to perform the following operations: (i) Move the content of Accumulator to register 7(R7).(ii) Move the contents of RAM memory location 55H to Port 1(iii) Receive content from ROM Memory location 200H into Accumulator.(iv) Clear bit 7 of the Accumulator.c) Why 4-20mA Current loop is widely used Industrial Standard for sensor data transmission and control. What are its advantages over 0-12V Standard? d) Two configurations of GPIB is shown in Fig. A and Fig. B. Explain the working of GPIB in both the configurations and what are the differences between the two. this question is asked in microcontroller and microprocessor
Create a subroutine using registers AX and BX with POP instructions, that subtract two 16bit numbers. Make sure that you preserve the values of AX and BX for use by the calling routine. Assemble, test and show your code with the calling routine pushing the following values on the stack: Value one = 1234h, Value two =4321h Result (hex) = _________________ Result (binary) = _________________ Result (decimal) = _________________