The following pseudocode algorithm has an error. It is supposed to use values input for a rectangular room’s length and width to calculate and display its area. Find the error. area = width × length. Display "What is the room's width?". Input width. Display "What is the room's length?". Input length. Display area.

The following pseudocode algorithm has an error. It is supposed to use values input for a rectangular room’s length and width to calculate and display its area. Find the error. area = width × length. Display "What is the room's width?". Input width. Display "What is the room's length?". Input length. Display area.

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter7: Arrays

Section: Chapter Questions

Problem 15PP: (Computation) A magic square is a square of numbers with N rows and N columns, in which each integer...

See similar textbooks

Similar questions

design a program for a professor to calculate the average of the three test scores for the students and congratulate the student enthusiastically if the average is greater than 95. here is the algorithm below. write the pseudocode for this program: 1. get the first test score. 2. get the second test score. 3. get the third test score. 4. calculate the average. 5. display the average. 6. if the average is greater than 95, congratulate the student.
Scenario: A robot is sitting in a chair with its arms facing down. Write an algorithm, using pseudocode, to make the robot: stand up walk until it senses a wall turn around walk back to the chair sit back down in the origin starting position Finally, output the total number of steps taken. Commands: In addition to our standard pseudocode commands, you must also use the following robot control commands: sit stand step (one step forward) raise arms (parallel to floor) lower arms (pointing to floor) sense (only if arms are raised) turn (90 degrees right) Immediately after issuing a sense command, you can check if the robot is at a wall.You do this via the boolean conditions "at wall" or "not at wall".The following are examples of this: if at wallif not at wallwhile not at wall AssumptionsYou must assume the following facts: The robot's initial sitting position is directly facing the target wall. There are no obstacles between the robot and the wall. The wall is 1 or more exact steps…
EXERCISE 2 Write an algorithm/pseudo code. Accept the two sides and an angle included by these two sides, and find the area and third side of a triangle. (1) Display "Enter two sides and an angle:"(2) Accept a, b,theta(3) ang = theta * 3.14 / 180;(4) third_side = sqrt (a*a + b*b - 2*a*b* cos(ang))(5) area = ½.0*a*b* sin(ang)(6) Display "Third_side =",third_side,"Area =", area(7) Exit
On a piece of paper write simple pseudocode that will compute for the area of a triangle.
Make a program that asks for a width, and then prints a pyramid of that width. The pyramid must be of odd width, and if the user enters an even number the program should print "Please enter an odd number" and ask again. (It is ok if the program gives an error if the user enters a non-number). Example: Please enter the pyramid width 10Please enter an odd numberPlease enter the pyramid width 14Please enter an odd numberPlease enter the pyramid width 13 * *** ***** ******* ********* ************************ The first line should have 1 asterisk, the second 3, then 5, 7, 9 etc. The number of spaces before starting the asterisks is (n−i)/2 Where n is the width of the pyramid and i is the number of asterixes in the current line. Note that this is always a whole number, as n and i are odd and hence (n-i) is even.
USE PYTHON A small shop sells 280 different items. Each item is identified by a 3 – digit code. All items that start with a zero (0) are cards, All items that start with a one (1) are sweets, All items that start with a two (2) are stationery and All items that start with a three (3) are toys. Write a program which inputs the 3 – digit code for all 280 items and outputs the number of cards, sweets, stationery and toys.
Write an algorithm that asks the user to enter 10 test scores and do the following:(a) Print out the highest and lowest scores.(b) Print out the average of the scores.(c) Print out the second largest score.(d) If any of the scores is greater than 100, then after all the scores have been entered, print a message warning the user that a value over 100 has been entered.(e) Drop the two lowest scores and print out the average of the rest of them.
Write and implement an algorithm that gets the amount of electricity used in kilowatt-hours and the cost of electricity per kilowatt-hour. Its output is the total amount of the electric bill, including an 8% sales tax. Write your answer to the following as multiple line comments at the beginning of your program.1. What are the data requirements of your program?2. Outline your algorithm using a pseudocode.
Please help me with this in Python In python Create a class Right triangle to compute its area and perimeter in class then self input of a b c like enter a: enter b: enter c: then output displays
Design an algorithm that will read two numbers and an integer code from thescreen. The value of the integer code should be 1, 2, 3 or 4. If the value of thecode is 1, compute the sum of the two numbers. If the code is 2, compute thedifference (first minus second). If the code is 3, compute the product of the twonumbers. If the code is 4, and the second number is not zero, compute thequotient (first divided by second). If the code is not equal to 1, 2, 3 or 4, displayan error message. The program is then to display the two numbers, the integercode and the computed result to the screen.
: An ant is sitting on an infinite grid of white and black squares. It initially faces right.At each step, it does the following:(1) At a white square, flip the color of the square, turn 90 degrees right (clockwise), and move forwardone unit.(2) At a black square, flip the color of the square, turn 90 degrees left (counter-clockwise), and moveforward one unit.Write a program to simulate the first K moves that the ant makes and print the final board as a grid.Note that you are not provided with the data structure to represent the grid. This is something youmust design yourself. The only input to your method is K. You should print the final grid and returnnothing. The method signature might be something like void printKMoves ( int K)
Design an algorithm that will receive two integer items from a user, and display to the screen their sum, difference, product and quotient. Note that the quotient calculation (first integer divided by second integer) is only to be performed if the second integer does not equal zero.