What is the total weight of this building?LevelRoof3rdThe following shows a schematic section of a three-storyreinforced concrete building. The building weights,elevations and seismic story forces are shown in the tablebelow.2Fo=1200 kFard 800 kF400 kStoryWeight(kip)3,000 k4,000 k4,000 k11,000kElevation(ft)4230Building Elevation and Seismic Story Forces154,000 kips8,000 kips11,000 kips12,000 kipsStoryforce, F(kip)1,2008004002,400kStory shear(kip)1,2002,0002,400Roof3rd Flr2nd FirStory overturningmoment(kip-ft)14,40044.40080,400

To Determine - The total weight of the building

The following shows a schematic section of a three-story reinforced concrete building. The building weights, elevations and seismic story forces are shown in the table below. What is the total weight of this building? F1200 k Far800k 400 k Roof 3rd Flr 2nd Fir

The following shows a schematic section of a three-story reinforced concrete building. The building weights, elevations and seismic story forces are shown in the table below. What is the total weight of this building? F1200 k Far800k 400 k Roof 3rd Flr 2nd Fir

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter16: Budget Estimating

Section: Chapter Questions

Problem 4RQ: Prepare a typical bay estimate based on the following information: a. Bay size of 350 feet and a...

See similar textbooks

Related questions

Q: Problem 7.2. Calculate the maximum stress induced in a cast iron pipe of external diameter 40 mm, of…

A: Given data : External diameter = 40 mm Internal diameter = 20 mm Length = 4 m Point load = 80 N A…

Q: Please summarize the structural seismic design procedure of pushover method.

A: In seismically active areas, seismic assessment is a crucial concern and an invaluable tool for the…

Q: Use superposition method to solve for the reactions at A, B, C. where EI is constant. Draw the shear…

A: Given: Required Support reaction and shear and moment diagram

Q: Considering the soil to be a uniform clay layer, estimate the primary consolidation settlement due…

A: This question is from Geotechnical Engineering.

Q: An extended layer of soil with homogeneous rounded grains has 10% of the material finer than 0.007…

A: Given: An extended layer of soil with, Homogenous rounded grains have 10 % The material finer than…

Q: In the soil profile shown, compute the vertical effective stress at points A, B, and C?

A: Effective stress is defined as the ratio of force at contact of particles of soil to the total area…

Q: A 14-inch square reinforced concrete column with tied transverse reinforcement is being considered…

A: To find the maximum permissible area of of vertical reinforcement provided that the, Column area =…

Q: Identify which of the four types of shown masonry blocks shown below might be used for: A fire rated…

A: Split-face brickwork is a desirable material in commercial construction projects because it is…

Q: Problem 3. Classify each of the structures as statically determinate or indeterminate. If…

A: As per our company guidelines we are supposed to answer only one question kindly repost other…

Q: TRUSS 1 2) How many zero-force members are there in the following truss? M Trussl Truss 2 1 2 E ( 2…

A: Brief concept introduction- Zero force members- Zero-Force Members are those structural members that…

Q: 30W २० 120k/0/m 3m 50kal 220/kulm k25 25m x asmx 1. SOLVE For the shear and moment diagram.

A: A simply supported beam with a hinged end at A and roller support at B, loading is as shown. To…

Q: In the following photo, identify the type of footing that is being installed. Photo A: Photo A:…

A: Given data in question Foundation site picture To find out Which type of Foundation is this

Q: A thin walled rotating shaft is subjected to a torque and a bending load. The torque produces the…

Q: Provide an in-depth discussion of how horizontal curve, vertical curve, and earthworks are connected…

A: One of the two crucial transitional elements in the geometric design of highways is the horizontal…

Q: Ab E 6 m 4 m 4 m B P₁

A: Given To find Zero force member

Q: Questions A stream is spanned by a bridge which is a single masonry arch in the form of a parabolic…

Q: 2 m A G B 1m F 2 m C E 1 m. P3 D P2

Q: A F E B D 4 m P₁

A: identifythe zero force members of the figure truss

Q: Downspout extensions are only utilized to maneuver around equipment or other obstacles to storm…

A: Reference : Water Resources, Water system. Given : A statement about downspout extensions. To…

Q: A E 6 m 4 m 4 m B P₁

Q: 12 lb/in. 8 in. 140 lb

A: Concept Here we will calculate the reactions at support using equations of equilibrium.Then…

Q: For the data shown in the table below find AWT, ADT, AADT and AAWT.

A: Answer Let us calculate the Total number of vehicle in weekdays and daily traffic Calculation of…

Q: Determine the peak hour volume Determine the peak hour factor Determine the design hourly volume…

Q: Using the given data in the traverse shown: POINTS AB C D E F NORTHINGS 75 m. 425 m. 675 m. 675 m.…

Q: A steel plate of width 120 mm and of thickness 20 mm is bent into a ircular are of radius 10 m.…

A: Given : Width of steel plate = 120 mm Thickness = 20 mm Radius of circular arc = 10 m E = 2 X 105…

Q: A 2 x 2 m flat plate solar collector for domestic hot water heating is shown in the figure. The…

A: Given, Area = 2m x 2m = 4 m2 Entering Temperature = 25oC Glass cover temperature = 27°C Air flow…

Q: From a solar observation fieldwork, the sun’s corrected altitude was determined to be 34°20’ and the…

A: Given data: Magnetic bearing = 34o 20' Declination = 25o10' Latitude = 50o 13' Determine the azimuth…

Q: P4-10) Create an orthographic projection of the following object. Draw the three standard views. .88…

A: An orthographic view is the two-dimensional result of an orthographic projection, usually consisting…

Q: A 14-inch square reinforced concrete column with tied transverse reinforcement is being considered…

A: Solution is attached below as

Q: Determine the midspan deflection. Use the Super Position method. A -3 m- B 25 kN/m CA +4 m -10 m-…

A: A simply supported beam of span 10 m is supported at B by hinge support at B and roller support at…

Q: Compute the resultant of the concurrent forces shown in N. P1 = 144 N, P2 = 326 N, P3 306 N, 01 = 11…

Q: In a certain portion of road to be constructed, the following data were taken. Station 1+ 0 20.00…

A: Given for station 1+0206.85+2.3 0+1.5 6.39+1for station 1+0706.0+2.0 0+1.…

Q: The direct shear test (DST) was conducted on the dense and loose sand, respectively. Please select…

Q: A square box beam is made of two 0.75 x 3-in. planks and two 0.75 x 4.5-in. planks nailed together,…

A: A ) V = 600 lb Spacing between nails = 1.75 inches To Find : Determine the shearing force in each…

Q: Problem 2. A sample of water is to be analyzed for solids content. Ten liters of water are passed…

A: Given:- The quantity of the water = 10 liter The initial weight of the filter = 15 grams The drying…

Q: Points of zero slope represent points where roadway goes from cut to fill or from fill to cut. a.…

A: Characteristics of mass curve: Points of zero slope represent points where roadway goes from cut to…

Q: Provide in-depth discussion of why Geodetic Engineers are important in construction survey

A: Geodetic engineers are responsible for creating and maintaining maps. Various technologies are used…

Q: Q1/ For an urban Highway, if the Average Annual Daily Traffic is (11000 v/d) in 2021and the annual…

Q: 3) Determine the force in members DF and EF, and EG of the truss shown below. 6 ft 6 ft 200 lb A₂…

Q: A loader operating at 107 cy/hr has 2.5-cy heaped capacity bucket and has a 1.2-min load cycle. The…

Q: find moment, reactions, shear and bending moments. ( please, show all calculations with units, )

Q: Write water absorption of Aggregate: 1-Introduction. 2-Procedure. 3- discussion .

A: Introduction - Water absorption of aggregate - it is used to understand the difference of apparent…

Q: Locate the centroid of the composite area and coose your own reference axes. Draw the location of…

Q: What other term is synonymous with texture in a rock? a. Specific gravity c. Streak b. Grain size d.…

A: C is the right option i.e Streak.

Q: P4-17) Create an orthographic projection of the following object. Draw the three standard views. 250…

A: To draw the orthographic projections.

Q: a non • sprinklered fire compartment temperature of 1170° F, what is the pressure difference at For…

Q: [(2x - (2x - x²) sin x dx

A: Given: Expression for integration

Q: XIV. Compound Curve The given elements for the compound curves are the following: Il = 35 degrees D1…

A: Given,I1=35 degreeI2=55 degreeD1=5.6 degreeD2=8 degreeTo determine,1) R1, R2,2) T1, T2, 3) L1, and…

Q: II. Theory of Errors 1. The distance from their home to their school has five measurements. The…

Q: Two coaxial cylinders, 10 cm and 9.75 cm in diameter and 2.5 cm high have both their ends open and…

Question

What is the total weight of this building?
Level
Roof
3rd
The following shows a schematic section of a three-story
reinforced concrete building. The building weights,
elevations and seismic story forces are shown in the table
below.
2
Fo=1200 k
Fard 800 k
F400 k
Story
Weight
(kip)
3,000 k
4,000 k
4,000 k
11,000k
Elevation
(ft)
42
30
Building Elevation and Seismic Story Forces
15
4,000 kips
8,000 kips
11,000 kips
12,000 kips
Story
force, F
(kip)
1,200
800
400
2,400k
Story shear
(kip)
1,200
2,000
2,400
Roof
3rd Flr
2nd Fir
Story overturning
moment
(kip-ft)
14,400
44.400
80,400

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given data

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An 8m steel tape was purchased and advertised as follows: Standard temperature : 24°CStandard Pull : 7.5kgsTape weight : 0.60 kgsCross sectional area : 0.049 sq.cm.A survey team was required to lay out a rectangular field officemeasuring 9.5m x 4.75m in the following field conditions:Ambient field temperature : 40°CActual pull : 13.2kgIn addition, the tape was supported on both ends and at midspanduring all measurements.** The modulus of elasticity of the tape is 2.03x106 kg/sqcm and the coefficientof thermal expansion is 0.0000116m/°C (25 pts)Answer the following: **Answers for corrections should be in 3significant figures. ex. (1.23x10-4)
What is the amount of loadthat applied to the center ofthe rectangular concrete beamsample if the Modulus ofRupture is 3.50MPa?Length of the sample = 550mmDimension: 150mm x150mm
What is over-consolidated?
What is shear starin rate?
SHOW COMPLETE SOLUTION PLSVALUES:X = 425C = 1
SHOW COMPLETE SOLUTION PLSVALUES: X = 425 C = 1
Pls help thanks
1. When is a building soft storey and why should we avoid it?2. Discuss Natural and Accidental torsion. Note: Please answer in an encoded form to be understood better. Thanks.
situation 2 pls ! COMPLETE SOLUTION ! *draw FBD * use data given properly
Topic: Quantity surveying 2.) The geometric method breaks the excavation into geometric shapes and calculates the volume for each of the shapes. true or false 3.) The data needed in estimating the roofing material are their effective widths and length in which they are available in the market. true or false 4. Because most equipment is not used on a project for an entire year, the costs must be converted to an hourly, weekly, or monthly cost. true or false
A concrete block whose volume is 0.023 cum is tied to one end of a wooden post having dimensions of 0.20x0.20x3.0m and is placed in sea water. If specific gravity of wood and concrete are 0.64 and 2.4 respectively: a. What is the length of wood projecting above the water surface? b. What volume of additional concrete anchor must be added to make sure that the wooden block will entirely submerge vertically in water?
load 1: 60 load 2: 50