The following table shows the results obtained from laboratory testsdone on samples of aggregates.Weight ofAggregates + BSG forMetalMetal Measure% ABS% MCSSDMeasureInside Diameter= 6 inchesHeight =12 inchesEmpty weight =8.62 kg30.39 kg2.673.699.241. Calculate the Dry Rodded Unit Weight of Aggregates in kg/m³.2. Calculate the % Voids in 1 m³ of aggregates.

Answer We are given Bulk specific gravity of SSD = 2.67 Weight of aggregates+metal container ( Wam…

The following table shows the results obtained from laboratory tests done on samples of aggregates. Weight of Aggregates + BSG for Metal Metal Measure % ABS % MC SSD Measure Inside Diameter = 6 inches 30.39 kg 2.67 3.69 9.24 Height = 12 inches Empty weight = 8.62 kg 1. Calculate the Dry Rodded Unit Weight of Aggregates in kg/m³. 2. Calculate the % Voids in 1 m³ of aggregates.

The following table shows the results obtained from laboratory tests done on samples of aggregates. Weight of Aggregates + BSG for Metal Metal Measure % ABS % MC SSD Measure Inside Diameter = 6 inches 30.39 kg 2.67 3.69 9.24 Height = 12 inches Empty weight = 8.62 kg 1. Calculate the Dry Rodded Unit Weight of Aggregates in kg/m³. 2. Calculate the % Voids in 1 m³ of aggregates.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

"A sieve analysis test was performed on a sample of fine aggregate and produced the following results:Sieve, mm 4.75 2.36 2.00 1.18 0.60 0.30 0.15 0.075 pan.Amount retained, g 0 33.2 56.9 83.1 151.4 40.4 72.0 58.3 15.6 .Calculate the percent passing each sieve, and draw a 0.45 power gradation chart with the use of a spreadsheet program. The specific steps or functions selected in the following description can vary somewhat depending on the version of the spreadsheet program being used.Calculate the fineness modulus of the sieve analysis results of Sample Problem
choose true or false If you know that weights of coarse aggregate as follow :Weight of aggregate stock = 5350 gm, weight of aggregate in oven dry= 5200 gm, weight of aggregate submerged in water =3254 gm, weight of aggregate SSD= 5220 gm , According to weights above , the oven dry bulk specific gravity is 2.325
A sieve analysis test was performed on a sample of aggregate and produced the results shown in Table .Calculate the percent passing through each sieve. Plot the percent passingversus sieve size on:a. a semilog gradation chart, andb. a 0.45 gradation chart (Figure A.25).What is the maximum size? What is the nominal maximum size?
determine the effective specific gravity of aggregates. DATA: Specific Gravity: Fine Agg = 2.603 Coarse Agg = 2.740 Asphalt Cement = 1.048 Percent By Weight: Fine Agg = 47.90 Coarse Agg= 47.78 Asphalt Cement= 100-FA-CA
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket =14L Weight of empty bucket = 9.21kg Weight of bucket filled with dry rodded coarse aggregate: Trial 1 =34,75 kg Trial 2 =34.06 kg Trial 3 =35.74 kg a. Calculate the average dry-rodded unit weight b.If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.
While measuring the abrasion value of sub-base aggregates category E sample was taken having dry weight of 10000 grams.Amount of fines passing through 1.7 mm sieve was 1550 grams. Workout the abrasion value of aggregates.
If Slump=120 Maximum size of aggregate=25 How is the amount of water interpolated ?
Specific Gravity and Absorption of Coarse Aggregates What are the possible discussion of observations for specific gravity and absorption of aggregate to observed values?
Table shows the grain size distributions of aggregates A, and B. Answer the following questions and show all calculations: What are the maximum sizes of aggregates A and B?
4. From the given data shown in the table below, determine the effective specific gravity of aggregates. Round off to two decimal places.
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:Volume of bucket = 12 ft3Weight of empty bucket = 20.3 lbWeight of bucket filled with dry rodded coarse aggregate:Trial 1 = 76.6 lbTrial 2 = 75.1 lb Trial 3 = 78.8 lba. Calculate the average dry-rodded unit weightb. If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.
Calculate the percent voids between aggregate particles that have been compacted by rodding, if the dry-rodded unit weight is 1410 kg/m3and the bulk dry specific gravity is 2.701.