None 3) The forward path transfer function of aunity feedback system is given below:KG(s) =s3 + s2 + s+aWhich of the following conditions will give astable open loop and a stable closed loopsystem?a = 2, K > 0a = 0.5 , 0.5 < K < 1a = 0.5 , -0.5 < K < 0.5a = 2, –0.5

Answered: Image /qna-images/answer/409abec4-5ef2-4c3a-8ab5-9a1cc3a19d2d.jpg

Answered: The forward path transfer function

Engineering

Electrical Engineering

The forward path transfer function

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For a unity feed back system, the open loop function is given by, G(s) = 90(S+9) / S2(S+2)(S+6) Determine the following: (i) The value of positional error constant is : (ii) The value of velocity error constant is : The value of acceleration error constant is : Which input signal can give correct error signal value?
The forward transfer function G(s) with a H(s) feedback configuration of an uncompensated Basic Satellite Launching System is as shown in figures 1 and 2. A- in the picture B- Compute the percent overshoot, peak time and settling time, using second order approximation through pole zero cancellation and unity feedback configuration shown in figure 2. C- Summarise the results (a) and (b) in tabular form and comment on the stability of both systems based on time response graph for (a) and computed values in (b).
Q2. Explain how you would determine the primary and secondary constants of transmission by impedance measurements. Also, explain how the velocity of propagation and attenuation constant can be experimentally determined.
The forward transfer function G(s) with a H(s) feedback configuration of an uncompensated Basic Satellite Launching System is as shown in figures 1 and 2. A- Write a m-script and generate the time and frequency response of the system shown in Figure 1. (a = 4, b = 2, c=2, d = 1and e=10, and f=4). B- Compute the percent overshoot, peak time and settling time, using second order approximation through pole zero cancellation and unity feedback configuration shown in figure 2.
A unity feedback system has loop transfer function: L(s) = Gc(s)G(s) = 4(s+z)/s(s+1)(s+3) a) Draw root locus as z varries from 0 to100 b) using root locus, estimate the percentage overshoot and settling time (within 2%) of system at z =4 c) determine actual overshoot and settling time at z = 4
Control System , Given transfer function, T (s) = αs + β / s^2 + (α + 2)s + β (i) Pick a pair of values for parameters α and β such that the closed-loop system is stable (ii) Pick a pair of values for parameters α and β such that the closed-loop step response exhibitszero steady-state error. (iii) Pick a pair of values for parameters α and β such that the closed-loop step response isunderdamped, exhibiting a settling time of 4/5 seconds and a peak time of π/7 seconds.
1. Use the Nyquist stability criterion to determine the ranges of K > 0 (if any) for which theclosed-loop system is stable.
In a closed-loop system, the system transfer function (G(s)) and the controller's transfer function (C(s)) areit is given as follows. According to this, the system is divided into a unit step, ramp and a parabolic entrancefind the permanent status error that it will give.
A directional coupler configuration with four ports is shown in Figure Q4. A 15 dBm power source is connected to port 1 resulting in coupling factor, C = 15 dB, directivity, D= 25 dB, and insertion loss L=0.5 dB. If all ports are matched,determine the power in dB at ports 2, 3 and 4.
Open loop function of a unity feedback system is given by G(s)=K(s+A) / s(s+1.4)(s+2.9)(s+3.2) For drawing root locus, if the value of Centroid is -2, then The value of A is :
are given a system’s transfer function as T(s) = 21 Construct a state-space model for the given system using ” Observer Canonical Form” method. | that the full state information of this system is available, design a state-feedback controller for this put the desired closed loop poles at ~2+ 2. Now, assume that the state information of the system are measurable, for this case what kind of controller do you suggest? Design this controller so that the ¢ Joop poles of the system are located at —10 + 510.
Hello, please solve this question , Greetings Q1. Choose the correct answer 1. Which among the following is not an advantage of an open loop system? a. Simplicity in construction & design b. Easy maintenance c. Rare problems of stability d. Requirement of system recalibration from time to time 2. Which notation represents the feedback path in closed loop system representation? a. b(t) b. c(t) c. e(t) d. r(t) 3. Which among the following represents an illustration of closed loop system? a. Automatic washing machine b. Automatic electric iron c. Bread toaster d. Electric hand drier 4. Transfer function of the system is defined as the ratio of Laplace output to Laplace input considering initial conditions________ a) 1 b) 2 c) 0 d) infinite Feedback can always reduce the effects of noise and disturbance on system performance? a) True b) False 6. Which among the following is not an advantage of an open loop system? a. Simplicity in construction & design b. Easy…