The four arms of a bridge supplied from a sinusoidal source are configured as follows: Arm AB: A resistance of 100 Q in parallel with a capacitance of 0.5 µF Arm BC: A 200 N noninductive resistance Arm CD: A 800 2 noninductive resistance , Arm DA: A resistance Rx in series with a 1 µF capacitance Determine the value of Rx and the frequency at which the bridge will balance. Supply is given between terminals A and C and the detector is connected between nodes B and D

The four arms of a bridge supplied from a sinusoidal source are configured as follows: Arm AB: A resistance of 100 Q in parallel with a capacitance of 0.5 µF Arm BC: A 200 N noninductive resistance Arm CD: A 800 2 noninductive resistance , Arm DA: A resistance Rx in series with a 1 µF capacitance Determine the value of Rx and the frequency at which the bridge will balance. Supply is given between terminals A and C and the detector is connected between nodes B and D

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Similar questions

2. A sinusoidal e.m.f. 110 sin 400t volts is connected in series in a circuit with an inductance of 0.1 henry , a re sistance of 10 ohms , and a capacitance of 250 * (10) ^ - 6 farad . Find the steady - state solutions of Q and I in terms of the time t. Also find the maximum values of the steady - state charge and current .
A 200V, 50 Hz sinusoidal supply is connected to a parallel network comprising three branchesA, B and C as follows: A, a coil of resistance 3 ohm and inductive reactance 4 ohm; B, a seriescircuit of resistance 4 ohm and capacitive reactance 3 ohm; C, a capacitor. Given that the powerfactor of the combined circuit us unity, find (a) the capacitance of the capacitor inF; (b) the current taken from the supply. [Ans. 127.32 F, 56A]
A sinusoidal 50 Hz voltage of 200 V (rms) supplies the following three circuits which are in parallel: (a) a coil of inductance 0.03 H and resistance of 3 ohms, (b) a capacitor of 400 microFarad in series witha resistance of 100 ohms and (c) a coil of inductance 0.02 H and resistance 7 ohms in series with a 300 microFarad capacitor. Find the total current supplied?
Consider the voltage v(t)= 40sin(100πt+140 o ) V. a) Find the period of this voltage in millisecond and the voltage value at t=6 ms. b) This voltage is applied to the circuit below. Find VR , VC and VL phasors and and draw them on the realimaginary axis. Find vR(t) , vC(t) and vL(t) via inverse phasor, comment phase angles. c) Find active, reactive and complex power (P,Q,S) on the inductor.
An AC Wheatstone bridge is supplied by 25V, 50Hz, which is shown in figure C5 is used to find the unknown values of inductance and capacitance. Determine the following, Figure C5 i. Calculate the value of C, if ZD is replaced as capacitor. ii. Calculate the capacitance of the capacitor, if ZD comprise of resistor, inductor and capacitor in series, with R=10 Ω, L = 20mH.
please write the complete solution and the topic is AC parallel circuits thank you A sinusoidal 50 Hz voltage of 200 V(rms) supplies the following three circuits which are inparallel (i) a coil of inductance 0.03 H and resistance 3 ohms,(ii) a capacitor of 40 microfaradin series with a resistance of 100 ohms, (iii) a coil of inductance 0.02 H and resistance 7 ohmsin series with a 300 microfarad capacitor. Find the total current supplied.
The parameters in the circuit are R1=0.1 Ω,ωL1=0.8 Ω, R2=24 Ω, ωL2=32 Ω, and VL=240+j0 V.1. Calculate the phasor voltage Vs.2. Connect a capacitor in parallel with the inductor, hold VL constant,and adjust the capacitor until the magnitude of I is a minimum.What is the capacitive reactance? What is the value of Vs?3. Find the value of the capacitive reactance that keeps the magnitudeof I as small as possible and that at the same time makes|Vs|=|VL|=240 V
11. Consider a network shown in the figure consisting of a resistance, a capacitor, an inductor and three alternating voltage sources 1, 2 and 3. Terminal voltages of the sources 1, 2 and 3 are v₁ = Vo sin(t), V₂ = Vo sin(cot +120°) and v3 = Vo sin(ot+240°) respectively and moduli of the reactance of the capacitor and the inductor are equal to the resistance. Then 10 3 P (A) Peak value of voltage at point P is vo (√3+1) (B) Peak value of voltage at point P is vo (√3-1) (C) Vp = Vo (√3+ 1) sin(oot +90) (D) vp = Vo (√3-1) sin(oot + 180)
Determine the capacitance and voltages (Vrms) across the resistor and capacitor and prove that the phasor sum of the series components is equal to the source voltage. Also, solve for its total circuit impedance and total circuit current.ps. we need a neat solution. thank you in advance!
Show that at a given frequency ω, the circuits will have the same impedance between the terminals a,b ifR1=R21+ω2R22C22,C1=1+ω2R22C22ω2R22C2.2. Find the values of resistance and capacitance that when connectedin series will have the same impedance at 40 krad/s as that of a1000 Ω resistor connected in parallel with a 50 nF capacitor.
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel Add the following two impedances (a) in series and (b) in parallel. Z1 = 4 + 3i and Z2 = 12 + 5i
In alternating current, AC, theory, the voltage through an inductor leads the current by a phase angle of 90°. Complex numbers can help in this situation as when a real number is multiplied by i it rotates through 90° on the Argand diagram, with the magnitude remaining the same. This allows us to specify the impedance through an inductor as a complex number. This can be combined with a resistor to give a combined impedance of z = r + Li. If we have two such elements in a circuit, we can use complex numbers to determine the total impedance when they are in series and in parallel. In series Zt = Z1 + Z2 In Parallel