The frame shown in the figure is supported by a hinge at A and a roller at E. Compute the vertical components of the hinge forces at C as they act upon member AC in kN. P = 55 k N and x = 5.7 m. Write numerical value only and in 2 decimal places. The frame shown in the Figure is supported by a hinge at A and a roller at E.Compute the vertical components of the hinge forces at C as they act upon memberAC in kN. P = 55 kN and x = 5.7 m. Write numerical value only and in 2 decimalplaces.3 m\D 1.5 mBMATHalino. O2 mk-1 m-eX*1 m→

P=55kN To find the vertical components of the hinge forces at C

The frame shown in the Figure is supported by a hinge at A and a roller at E. Compute the vertical components of the hinge forces at C as they act upon member AC in kN. P = 55 kN and x = 5.7 m. Write numerical value only and in 2 decimal places. 3 m P B o 1.5 m MATHalino 2 m

The frame shown in the Figure is supported by a hinge at A and a roller at E. Compute the vertical components of the hinge forces at C as they act upon member AC in kN. P = 55 kN and x = 5.7 m. Write numerical value only and in 2 decimal places. 3 m P B o 1.5 m MATHalino 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate for the axial force in kN at member GC of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
In the figure, the rigid AD bar is held vertically by two elastic rods articulated at the ends, which are horizontal at points B and C. Under the effect of a horizontal load of 120 kN of the system; a) Calculate the forces to occur in the elastic bars, b) The displacement of the top point (A) of the rigid bar. Note: (EA = 108N)
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Draw a free body diagram of rigid bar ABD, and determine the magnitude of the vertical reaction force at pin D.Answer:D = kN
Using CONJUGATE BEAM METHOD, Consider 150 mm x 200 (b x h) mm section and E = 80 GPa. Enter the absolute value only and round-off your answer to 3 decimal places. GIVEN: a = 2.4 m b = 14.8 kn/m c = 45 KN QUESTIONS: 1. Determine the REACTION at D in KN. 2. Determine the MOMENT REACTION at A in KN-M. 3. Determine the DEFLECTION at B in MM. 4. Determine the DEFLECTION at C in MM. THANK YOU! PLEASE ANSWER ALL. ❤️
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Determine the internal force and the change in length of section (1) of axial member CDE. Tension and elongation are positive. Compression is negative.Answer:F1 = kNδ1 = mm
The beam shown in the figure has a slidingsupport at A and a roller support at B. The slidingsupport permits vertical movement but no rotation.Derive the equation of the def lection curve anddetermine the deflection δA at end A and also δC atpoint C due to the uniform load of intensity q =P / Lapplied over segment CB and load P at x =L / 3. Usethe second-order differential equation of the deflectioncurve.
The continuous beam shown in the figure is fixed at both ends A and D, and supported by rollers at B and C Assume I = 800 x 106 mm4 and E = 70,000 MPa. W1 (kN/m) = 25 F (kN) = 50 S (mm) = 15 If there is a settlement of S at the support C, solve the following: 1. Slope at B, in radians 2. Slope at C, in radians 3. Reaction at A, RA in kN 4. Moment at A, MA in kN-m 5. Reaction at D, RD in kN 6. Moment at D, MD in kN-m
The frame shown in the figure is supported by a hinge at E and roller at D. Compute the horizontal and vertical component of the hinge force at C. as it acts upon BD *use 3 decimal place in rounding off all throughout the solution.
In the system shown in the figure, parts AB, BC and CD are of equal length and 4 m. Clockwise from point AA moment of 10 kNm is applied in the opposite direction. The distributed load of 3 kN/m at BC is upward. Beam DA load of 5 kN was applied downwards from the point. The profile of the beam has a 100 mm edge as seen on the right side.was formed by subtracting a circle with a diameter of 80 mm from the center of a regular hexagon of length. Accordingly; A)Calculate the reaction forces at B and C B)Draw shear force and bending moment diagrams C)Calculate the maximum bending and show it on the bending moment diagram. D)Calculate the sectional moment of inertia of the profile E)Calculate the maximum stress in the beam NOTE:For option C, you need to obtain a parobolic expression when drawing the bending moment diagram. You need to use derivation.
Solve for e e^(−k/5) − 2 =10 Solve for n 2log4(3n−5)+5=9
The crankshaft is subjected to a torque of M = 50 N ⋅ m. Determine the horizontal compressive force F and plot the result of F (ordinate) versus θ (abscissa) for 0° ≤ θ ≤ 90°.
USING CONJUGATE BEAM METHOD Consider 150 mm x 200 mm (bxh) mm section and e = 80 GPa DETERMINE REACTION AT D Values: A = 9.4 M B = 5.5 kN/m C = 20 kN