i need the answer quickly The full-bridge inverter has a switching sequence that produces a square wavevoltage across a series RL load. The switching frequency is 60 Hz, V = 100 V, R = 10 N,and L = 25 mH. Dctermine (a) an expression for load current, (b) the power absorbed bythe load, and (c) the average current in the de source.1 SolutionT 1/f = 1/60 = 0.0167 s LIR = 0.025/10 = 0.0025 s T/27 = 3.33

Answered: Image /qna-images/answer/93a971c3-b348-4419-be4b-64b03b28c5e5.jpg

The full-bridge inverter has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Vd = 100 V, R = 10S and L = 25 mH. Determine (a) an expression for load current, (b) the power absorbed b the load, and (c) the average current in the de source. 1 Solution T= 1/f = 1/60 = 0.0167 s = LIR = 0.025/10 = 0.0025 s] T/27 = 3.33 %3D

The full-bridge inverter has a switching sequence that produces a square wave voltage across a series RL load. The switching frequency is 60 Hz, Vd = 100 V, R = 10S and L = 25 mH. Determine (a) an expression for load current, (b) the power absorbed b the load, and (c) the average current in the de source. 1 Solution T= 1/f = 1/60 = 0.0167 s = LIR = 0.025/10 = 0.0025 s] T/27 = 3.33 %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A basic inverter with unidirectional switches is connected to a resistive load. The peak supply current is 50 A, then the peak transistor and load currents are respectively: Select one: a. 25 A, 50 A b. 25 A, 25 A c. 50A,50A d. 50 A, 25 A e. None of these
I'll give upvote, thanks. Consider the transistor inverter driving a DC motor modelled as a 1.2mH inductor. The input voltage vi=5V for t<0s. Assume β=75, VBE,ON=0.7V and VCE,SAT=0.2V. Let R1=500Ω, R2=330Ω, and R3=10KΩ. At t=0s, vi decreased from 5V to 0V. Determine iL(0-), iL(∞), v0(0-), v0(0+), v0(∞), time constants for t<0s and t>0s, iL(t) for t>0s and v0(t) for t>0s.
The single-phase half-bridge inverter has a resistive load of R = 2.4Ω and the DCinput voltage is 48V. Determine:1- the rms output voltage at the fundamental frequency2- fundamental displacement factor .3- fundamental power , drown from each source .4- fundamental load power .5- total power drown from each source .6- total load power .
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50Hz on the series RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma = 0.9 and frequency modulation rate mj = 19. The resistance of the series RL load is 15 ohms and the coil inductance is 40 mH. What is the total harmonic distortion value (THD) of the power drawn by the load resistor and the load current?
Apply inverter parameter analysis equations to solve the followings for Single phase full bridge inverter. Asume inverter is used for home application to drive resistive load of ‘A’ ohm with DC battery of 60V as input. (a) Required output power (b) Average current across each transistor (c) Total harmonic distortion THD (d) Harmonics & distortion factor of 5th harmonic and (e) Draw its complete diagram Also here A= 4
A single-phase full bridge inverter is operated from a 48V battery and issupplying power to a resistive load of 10 Ω. Determine:(i) The fundamental output voltage and first five harmonics.(ii) RMS value by direct integration method and harmonic summationmethod.(iii) Output rms power and output fundamental power.
For single phase inverter has the followingparameters ; Vac = 80v , R = 80 , L = 20mHand f = 60 Hz Determine total harmonic distortion for n = 5 ; thenwrite expression for voltage
In a lowering converter, the input voltage is Vs = 20V, the output voltage is Va = 10V, and the average value of the load current is Ia = 1.0A. The switching frequency is set to 50 kHz. If the inductance value in the inverter is L = 100 μH and the capacity value is C = 200 µF (a) the duty ratio of the switch D (b) the ripple / ripple (ΔI) value of the coil current (c) the ripple / ripple (Vc) of the output voltage and (d) the switching Calculate the maximum current passing through the element. Draw the waveforms of coil current (iL), switch current (isw) and diode current (i1) in the area below for a switching period according to these values.
What factors contribute to the overall system efficiency of a solar pv system (that is system efficiency = system output/solar radiation reaching panels)? List all that apply. -panel efficiency -capacity factor -angle of incidence -inverter efficiency -derating factors (dirt, temperature)
Consider the transistor inverter on the right driving a long cable, modelled as a 0.1uF capacitance. The input voltage vi=0V for t<0s and 5V for t>0s. Assume β=100, VBE,ON=0.7V and VCE,SAT=0.2. Determine v0(0-), dv0(0+)/dt, vo(t) (use general step formula, assume transistor is initially forward active), and compute how long it takes to enter saturation.
Using MOSFET design your own circuit such that it works as an inverter. (Hint: When input = high the output = low and vice versa) NOTE: DRAW USING SOME KIND OF CICUIT SOFTWARE(CIRCUIT WIZARD.LIVE WIRE or Any other online software) Hand made not accepted please
4) A single phase full bridge inverter will be used to generate 50 Hz square wave voltage. Inverter the input voltage is 400 V and the load consists of inductance and resistance connected in series. (R=10Ω, L=31.83 mH) a) Draw the circuit b) Plot the load current, showing the load voltage and semiconductor currents. c) Load voltage is effective calculate the value d) Calculate the effective value of the main harmonic of the load current. e) Calculate the average load current. f) Find the THD of the load voltage