The gate is b=5m wide, is hingedat point B, and rest against ay = 10050N/m³15msmooth wall at point A.Find6m(a)The force on the gate exerted by8mseawater pressure(b)The horizontal force P.exertedby the wall at point A .

Name: The gate is b=5m wide, is hingedat point B, and rest against ay = 100
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The gate is b=5m wide, is hingedat point B, and rest against ay = 10050N/m³15msmooth wall at point A.Find6m(a)The force on the gate exerted by8mseawater pressure(b)The horizontal force P.exertedby the wall at point A .

Answered: Image /qna-images/answer/baef1bcd-510d-432a-937d-23e8b293625c.jpg

Engineering

Mechanical Engineering

The gate is b=5m wide, is hinged y = 10050N/m³ at point B, and rest against a 15m smooth wall at point A. A Find 6m (a)The force on the gate exerted by 8m seawater pressure (b)The horizontal force P exerted by the wall at point A.

The gate is b=5m wide, is hinged y = 10050N/m³ at point B, and rest against a 15m smooth wall at point A. A Find 6m (a)The force on the gate exerted by 8m seawater pressure (b)The horizontal force P exerted by the wall at point A.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the lid (D = 4 m). If the weight of the lid is neglected, it is necessary to keep the lid in balance. Find the size of the force (Fa) required, as shown. Take the density of the water as 999 kg / m3.
Q 244 What are the reaction forces on the latch an djoint in the gate below? And in case thefloodgate is reversed (concave)? *The gate is a cylinder room with length L = 5 m
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Figure. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B.Determine the force exerted on the plate by the ridge.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown in Fig. below. The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate by the ridge.
A 6-m-high, 5-m-wide rectangular plate blocks the end of a 5-m-deep freshwater channel, as shown . The plate is hinged about a horizontal axis along its upper edge through a point A and is restrained from opening by a fixed ridge at point B. Determine the force exerted on the plate by the ridge
A dam with triangular cross section holds back a body of water. The dam has height h. The dam is made of concrete, which has speci…c gravity 3.1. What is the maximum angle, , for which thedam will not tip over about point O?
An open tank 2 m x 4 m rectangular horizontal section has anegligible weight and contains water to a depth of 1.5 m. It is actedupon by an unbalanced force of 50 kN parallel to longer side so thatwater is about to spill. If the tank is closed and theacceleration is increased by 4 m/s ², determine the new unbalancedforce if the pressure on the surface is 30 kPa.
plzzzzzzz help What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
A pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively
The 100cm radius cylinder weighs 3.1 KN and rest on the bottom of a container which is 1.5 meter long. Oil and water are poured into the left and right portion of the container to the depth of 0.8m and 1.4m respectively. Find the magnitude of the horizontal and vertical components of the force which will keep the cylinder touching the container at B.
Piston A has a cross-section of 1,200 cm2 while that of B is 800 cm2. B is higher than A by 200cm. If the intervening passages are filled with oil and a force of PB=4.6kn is acting on B. What must be the pressure in N/m2 exerted at A?