The given angle bar L125x75x12mm with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: a. ultimate tensile strength (kN) based on tensile rupture

The given angle bar L125x75x12mm with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: a. ultimate tensile strength (kN) based on tensile rupture

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Related questions

Q: Please provide the enough information and definition of these construction terms: Dam Dead line…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Problem No. 1 Using double integration method to determine the value of X that must be applied at…

Q: Explain Fire Barriers and how they differ from Fire Partitions?

Q: Determine the maximum thickness (t) of the specimen if it is subjected to a force P = 5 KN. The bar…

A: Consider below figure ; At A ; σ = PA 100 = 5 × 100037.5 t t = 1.333 mm --------- 1

Q: Use Moment Area Method to find the EIy value at the midspan

A: ∑MA=04000 + 2000×8 + 4000 - RC×16 = 0 RC=1500 lb ↑∑V=0RA+RC=2000RA+1500=2000RA=500 lb ↑Bending…

Q: Problem #1 A W12 x 72 is used as a column having an unsupported height of 4.6 m. The column has a…

A: Given -

Q: Given data : Force=0.5 N Displacemnt=1 m Determine work done

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

Q: NOTE: This is considered as a FRAME WITHOUT SIDESWAY Using the Moment Distribution Method (MDM) w…

A: MFDA = -17x6x3 =-306 kN-m

Q: A system of three pipes 600 m, 800 m, and 1000 m long that are connected in series carries 600 L/sec…

Q: ral condition a soil sample has a mass of 2290 g and a volume of 1.15x10 m. After being completely…

Q: The boom AC is a 120 mm square steel tube with a wall thickness of 7.5 mm. The boom is supported by…

Q: 10. A deed describes a trapezoid shaped parcel, but is missing the last call to the point of…

A: Closed traverse A closed traverse is a set of linked lines, the lengths, and bearings of which are…

Q: The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa;…

Q: 3. The tank in the figure is filled to its top with gasoline. If the truck has a constant…

Q: 5.18 (B). A uniform horizontal beam ABC is 0.75 m long and is simply supported at A and B, 0.5 m…

Q: The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi;…

A: Calculating support reactions

Q: Q2) What is the value of K for a column with fixed ends when using the direct analysis method? a)…

A: Note: As per our policy for multiple questions only 1 question can be solved for others please…

Q: What is the fixed end moment FEMas for the beam with a settlement of 25 mm at support C? 20 kN/m 60…

A: Figure is as shown

Q: 208. Calculate the quantity of the sand required (in cubic meter) in 20 cubic meters of reinforced…

Q: [U.Birm.] [-20, - 66.5, 0kN m; 85.7, 130.93, 13.37 kN.] 5.21 (B). A continuous beam ABCD is simply…

A: Assumption We considered EI constant everywhere.

Q: Steel joists are manufactured in different series to account for which of the following?…

A: Steel joists- Steel joists are an open web, lightweight metal trusses with matching hooks and a…

Q: Calculate the quantity of the sand required (in cubic meter) in 20 cubic meters of reinforced cement…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: Problem 8: A-C fc=4500 psi 2 in Grade 60 #6 bars - # 4 stirrups 1.5 in. clear cover 3/4 in. max.…

A: Given data: f'c=4500psi=31Mpafy=Grade 60=415Mpaeffective depth=d=20in=508mmMaximum depth ofneutral…

Q: Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its viscosity is 1.15x10-7…

Q: P A L L Calculate the deflection at A (the end opposite of the load) and at D (under the load).…

Q: Some data from this technical description is unreadable due to flooding from a super typhoon. Solve…

Q: 1. A 30-m tape having a standard length of 30.005 m is to be used to lay-out a building that has…

Q: the parabolic cable shown carries a uniform load of 120 kN/m. the lowest point of the cable is…

A: Figure is as shown

Q: From the figure shown, Determine: The plastic section modulus about the horizontal axis. x10^6 mm^3…

Q: For the cantilever steel beam [E = 190 GPa; I = 82 x 106 mm4), use the double-integration method to…

Q: 4. If the open cylindrical container rotates at an angular velocity of 8 rad/s, determine the…

Q: For the cantilever beam shown on the above figure, determine the following: Shear force at B - ____…

A: As per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: An aluminum pipe has a length of 59 m at a temperature of 11°C. An adjacent steel pipe at the same…

Q: Mass = 15 kg Velocity = 16m/.

Q: B- EVEN : The steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. is carrying…

Q: KINDLY OBTAIN THE RIGHT ANSWER AND EXPLAIN Refer to Figure. Given that B =1 m, L = 3 m, and Q = 110…

A: Given - Given that B =1 m, L = 3 m, and Q = 110 kN, the soil characteristics given in the figure…

Q: Situation 22. For the built-up shape shown in the figure, determine: В. bf = 200 mm — 12 тт hE 200…

Q: 4. A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of…

Q: Ep1 = με Ep2 = με Ymax in-plane prad Vabsolute max. prad 0p =

Q: Determine the product of inertia with respect to the x and y axes for the shaded area shown. Hint:…

A: To find product of inertia

Q: 1. Strength of properly dried wood is significantly higher than that of green (freshly cut) wood. 1.…

A: Explanation : The use of seasoned or properly dried wood over green/ freshly cut wood is more…

Q: An aluminum association standard l-beam 8x6.8181, uniformly distributed load of 1125lb/ft over a…

A: Figure is as shown

Q: A reinforced concrete T-beam has the following properties: Flange width, bf = 1,350 mm Width of web,…

A: Answer Flange width (bf) = 1350 mm Web width (bw) = 300 mm Total height h = 500 mm effective depth d…

Q: General contractor General specification Gravitational acceleration

A: 1. General Contractor A General Contractor is the actually defined as an individual or a company…

Q: A reinforced concrete T-beam has the following properties: Flange width, bf = 1350 mm Width of…

Q: Calculate the quantity of the sand required (in cubic meter) in 20 cubic meters of reinforced cement…

A: given- volume of the RCC=20 cubic metersRCC ratio (1:2:4)

Q: What are the issues/factors involved in transportation safety? Elaborate.

A: Que:- What are the issues/factors involved in transportation safety? Elaborate.

Q: A spiral easement curve has a length of 120m with a central curve having a radius of 300m. Determine…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

a. ultimate tensile strength (kN) based on tensile rupture

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The given angle bar L125x75x12mm with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: a. nominal tensile strength (kN) based on gross yielding.
The figure shows a plate having a width of 400 mm and thickness of 12 mm is to be connected to another plate by 34 mm diameter bolts as shown in the figure. Assume diameter of holes to be 2 mm larger than the diameter of the bolts. Use A 36 steel plate with yield strength Fy = 248 MPa and minimum tensile strength Fu = 400 MPa. For a chain holes extending across a part in any diagonal or zigzag line, the net width of the part shall be obtained by deducting from the gross width the sum of the diameters or slot dimensions of all holes in the chain and adding, for each gage space in the chain, the quantity S24g where S is the longitudinal center to center (pitch) of any consecutive holes, in millimetres and g is the transverse center to center spacing (gage) between fastener gage lines in millimetres. If a = 60 mm, c = 150 mm and d = 100 mm. Determine the nearest value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Determine the nearest value…
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the design strength due to yielding in the gross section. (kN)
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area?
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
The magnitudes of the three forces applied to the eye bolt are T1 = 100lb, T2 =50lb, and T3=170lb. Replace these forces with a single equivalent force R. Show the result on a sketch of theeye bolt.
The following figure shows a cantilever beam with b = 305 mm containing three D-22 bars that are anchored in the column by standard 90 hooks. f. 42 MPa (normal-weight) and f=420 MPa. If the steel is stressed to f, at the face of the column, can these bars (a) be by hooks into the column? The clear cover to the side of the hook is 70 mm: The clear cover to the bar extension beyond the bend is 51 mm. The joint is enclosed by ties at 150 mm o.c.
Determine: Ix & ly = Moment of inertia about axis XX and YY Rx & Ry = Radius of gyration about axis XX and YY Sx & Sy = Elastic modulus about axis XX and YY steel specs are here http://www.toolsforengineer.com/steel-sections-properties-tables/ FOR WIDE FLANGE = W250X22FOR ANGLE BAR = L32X32X6.4
Two steel plates are welded to a rolled W section as indicated. If the area and the centroid location of each subsection are given in the table below, what is the moment of inertia with respect to x axis? (Height of W14x38 section is 14.1 inches.)
The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.
The figure as shown below is a rigid bar (ABCD) which was supported thru pin at B. Two bars was also connected, Bar CE and Bar DF with corresponding cross-sectional area and Modulus of Elasticity. If P is equivalent to 94 kN, the diameter at pin B is Blank 1 mm. with drawing and complete solution
Calculate the design moment strength of a rectangular section with the following details: b = 250 mm, d = 440 mm, d′ = 60 mm, tension steel is six bars 25mm in diameter (in two rows), compression steel is three bars 20mm in diameter, f ′c = 20MPa, and fy = 350MPa.