The given perpendicular offsets were taken at 10 m intervals from a survey line to an irregular boundary lin - 3.82, 4.37, 6.82, 5.26, 7.59, 8.90, 9.52, 8.42, and 6.43 m. Calculate the area in sq.m between the survey line, the irregular boundary and the first and last offsets by the application of (a) Simpson's rule and (b) the Trapezoidal rule.

The given perpendicular offsets were taken at 10 m intervals from a survey line to an irregular boundary lin - 3.82, 4.37, 6.82, 5.26, 7.59, 8.90, 9.52, 8.42, and 6.43 m. Calculate the area in sq.m between the survey line, the irregular boundary and the first and last offsets by the application of (a) Simpson's rule and (b) the Trapezoidal rule.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The given perpendicular offsets were taken at 10 m intervals from a survey line to an irregular boundary line: - 3.82, 4.37, 6.82, 5.26, 7.59, 8.90, 9.52, 8.42, and 6.43 m. Calculate the area in sq.m between the survey line, the irregular boundary and the first and last offsets by the application of (a) Simpson’s rule and (b) the Trapezoidal rule. Subject: engineering surveying
From a transit line to the edge of a river a series of perpendicular offsets are taken. These offsets are spaced 4.0 m apart and were measured in the following order: 0.5 m, 1.4 m, 2.5 m, 5.6 m, 8.5 m, 7.4 m, 3.8 m, 5.1 m, and 2.3 m. Determine the area included between the transit line, the river’s edge and the line offsets using (1) Trapezoidal Rule, (2) Simpson’s One-Third Rule.
course subject: Fundamentals of surveying I. PROCEDURE Establish at least six traverse stations at designated points on the field assigned to be surveyed. Call these stations (or corners) A, B, C, etc. Set the instrument Sight instrument on the last traverse station and read the magnetic bearing. Record this as the back bearing of the line in the traverse. 4.Sight B and read the instrument. Record this as the forward bearing of line AB.
Surveying In order to locate the position (P) of a sounding boat, the angles APB & BPC subtended at P by three points A, B and C on the shore were measured with a sextant and found to be 28º 42’ 40” and 30º 28’ 20” respectively, the point B & P being on opposite of AC. The length of AB & BC scaled from a map were 662 m and 4662 m respectively, and the angle ABC was 60º 50’ 40”. Carry out all the necessary calculations to compute the distances PA, PB and PC.
Elementary Surveying: Measurement of Horizontal Distances, show proper and right solution. 1. A line AC cannot be measured directly because of an obstruction on theline. Accordingly, the two lines AB and BC were measured as 2,357.90mand 1,846.00m, respectively. Point B was set at a perpendicular distanceof 225m from point D on line AC. Using the approximate slope correctionformula for steep slopes, determine the length of line AC. Illustrate.
to find out the included angles in a closed survey PQRSTP, the following observations were made with the compass. calculate the included angles after correcting the local attractions line fore bearing(FB) back bearing(BB) PQ N 620 45/E S 62015/W QR N 210 00/W S 200 45/E RS N 710 30/W S 710 30/E ST S 390 00/W N 380 00/E TP S 540 30/E N 530 15/E
The following offsets were taken at 20 m intervals from a survey line to an irregularboundary line 0.00, 3.50, 4.30, 6.75, 5.25, 7.50, 8.80, 7.90, 6.40, 4.40, 3.25, 0.00 mCalculate the area enclosed between the survey line, the irregular boundary line, and theoffsets, by:a) the trapezoidal ruleb) simpson’s rule
Plan-view sketches of benchmark leveling runs are shown below. Along each line representing a sight is the value of the rod reading for that sight. The numbering of the TPs shows the direction of the level run. Place the data in the form of field notes. Include the arithmetic check. Assuming that the average length of each BS and FS is 145 ft, determine the accuracy of the survey.
elementary surveying A line AC cannot be measured directly because of an obstruction on line. Accordingly, the two lines AB and BC were measured as 2,357.90m and 1,846.00m, respectively. Point B was set at a perpendicular distance of 225m from point D on line AC. 1.Using the approximate slope correction formula for steep slopes, determine slope correction for AB. 2.Using the approximate slope correction formula for steep slopes, determine slope correction for BC. 3. Determine the length of line AC.
What is profile leveling and what is the purpose of profile leveling?
Identification ______ are horizontal angles observed clockwise from any reference meridian. The average height for the surface of the seas for all stages of tide over a 19-year period as defined by the National Geodetic Vertical Datum of 1929 Area by DMD and DPD Method requires _______ departures and latitudes normally obtained in traverse computations The acute horizontal angle between a reference meridian and the line are known as It is a series of consecutive lines whose ends have been marked in the field and whose lengths and directions have been determined from observations The DMD of the first course is its ________ rule adjusts the departures and latitudes of traverse courses in proportion to their length The DPD of the first course is its ______ It is the general term applied to any of the various processes by which elevations of points or differences in elevation are determined. ______ units are units of angular measurement are the degree, minute, and second. A…
If a plus sight of 1.097m is taken on BM A, elevation 305.348m, and a minus sight of 0.832m is read on point X, calculate the HI and the elevation of point X.