Answered: The heat capacity of a liquid is 250…

The heat capacity of a liquid is 250 J/K, if its mass is 50 kg the specific heat capacity of the liquid would be 1250 J kg/ K C° 50 J kg/ K C° 125 J kg/ K C° 5 J kg/ K C°

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.56P: A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss...

See similar textbooks

Related questions

Q: The net work produced by a Gas Turbine Power plant is 85 BTU. What is the efficiency of the said…

A: The efficiency of the gas turbine power plant is 81.97 %.

Q: 2 m 10 m

A: As this question is multipart, I will be solving only one question. Diameter of the cylinder is 2…

Q: An ideal reheat rankine cycle is characterized by a steam generator pressure of 11 MPa and a…

Q: Modified Sinusoidal function is composed of a) Only one sine function b} Two sine function with…

A: Modiefied Sinusoidal Funtion

Q: Summarise and discuss the differences between CNC programs (G-code programs) for CNC machining and…

A: Given question: Summarize and discuss the differences between CNC programs (G-code programs) for CNC…

Q: Forida Tidal power plant is one of the famous. officient tidal plant. What is the energy or power…

A: Barrage area, Abarrage= 1820 m2 vertical height range, hvertical = 3.2 m Sea water density, ρsea…

Q: Given data : Force=2 N Area =0.2 mm2 Determine stress

A: Given:- Force = 2 N Area = 0.2 mm2 To Find:- Stress

Q: If the cord is subjected to a horizontal force of P = 146 N, and the gear is supported by a fixed…

Q: Completely determine the resultant of the forces shown in the figure. Option: R= 957lb down to the…

Q: A closed system is comprised of 10kg of pure water substance initially at a temperature of 400 C and…

Q: Two blocks are connected by a solid strut attached to each block with frictionless pins. If the…

A: Given : To find : Maximum weight of A to maintain equilibrium

Q: Q3: The 10 kg slender bar is attached to the small roller A, which glides freely along the groove.…

A: Find the angular acceleration of the bar and the acceleration of the roller immediately after it is…

Q: the value of B is

A: Given; Maximum value of W to avoid buckling of the beam isobtained as βπ2EI, where, πis the…

Q: A key is to be designed for a 12.7cm shaft which will transmit power of 150kW @ 360 rpm. If the…

Q: The simply supported beam is built up from three boards by nailing them together as A, shown.…

A: Find the spacing of nails.

Q: i need the answer quickly

A: For quarter circle, r= 150 mm X1 = 4r/3π =4×150/3π= 63.662 mm Y1 = 4r/3π =4×150/3π= 63.662 mm…

Q: Substances with higher specific heats will increase in temperature faster than substances with lower…

A: Specific heat of a substance : It is defined as the net quantity of heat required to raise the…

Q: 2. Multiple expansion valves Condenser -3 P 2

A: ME-VCS (multi-evaporator vapour compression systems) are used to cool numerous zones. The…

Q: Compute the Total work of a plant if the the combined cycle overall efficiency is the average value…

A: Combined cycle overall efficiency is the average value Heat input= 192 kJoules= 192000 Joules To…

Q: A circular aluminum tube of L=600mm is loaded in by compressive forces at its ends. The outside and…

A: Answer: (a) The load P is 74.1353 kN. (b) The shortening of the tube is -0.4686 mm and the percent…

Q: The R-ratio (minimum stress to

A: Given data; Determine the R ratio for this cyclic loading.During a high cycle fatigue test, a…

Q: Most modern electrical heating and cooling devices are provided with thermostat. What is the purpose…

A: given; Most modern electrical heating and cooling devices are provided with thermostat. What is the…

Q: If a Carnot cycle operates at temperature limits of 283 K and 319 K, determine the ratio of the work…

Q: A Kaplan turbine has a runner diameter of 4 m and a hub diameter of 1.2 m. The discharge through the…

A: The runner diameter is 4 meter and the hub diameter is 1.2 m. The discharge of the fluid through…

Q: Assume the stabilizer of an airplane is a flat plate. If the transition /critical RN 750,000, what…

A: Given data as per the question RN=750000v=44.7 mschord length =0.81 mrectangular stabilize having…

Q: SA2) A 2000-kg truck is parked 5.0 meters from one end of a bridge while a 1500-kg van is parked…

A: GIVEN: * 2000 Kg truck parked 5.0 m from one end. * 1500 kg Van parked 7.50 m from the opposite end.…

Q: A glass window has the shape of a trapezoid with height 4m, width at the top of 5m, and width at the…

A: Given h=4m a=5m b=8m y=3m

Q: 2.77 A steel rod 3 ft long with a cross-sectional area of 0.3 in.² is stretched between two fixed…

Q: Two long, silver rods (k = 400 W/mK, diameter = 10 mm) are soldered together end to end, with the…

A: When an amount of heat is supplied from the one solid body to the another solid body due to…

Q: A perpetual motion machine is a machine that never stops, hence its name. It is a machine that can…

A: Concept: 1) First law of thermodynamics: It states that energy neither be created nor destroyed but…

Q: Q1: The rope is wrapped around the central core of the 95 kg coil, whose rotating radius relative to…

A: Given data:

Q: What is the maximum speed that the one-ton vehicle can travel over the hill and not lose contact…

Q: The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I…

Q: A pipe line used to transport oil from one area in Dubai to Kuwait carrying a temperature of 30℃ of…

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

Q: The tank is used to store a liquid having a specific weight of 80 lb/ft^3. If it is filled to the…

Q: The figure shows a weapon called a battering ram (modern large battering rams are typically mounted…

Q: Assume perfect elastic impact. Immediately after

A: Given; Asssume perfect elastic impact. immediateley after the impact.A ball A of mass m falls under…

Q: A young man saw his lover having a date with another man at the park. The young man confronts his…

A: Given data Young man runs with an acceleration 2.788 ft/s2 N15°W = 0.8498 m/s2 N15°W Girl runs…

Q: A Kaplan turbine has a runner diameter of 4 m and a hub diameter of 1.2 m. The discharge through the…

A: The runner diameter is 4 meter and the hub diameter is 1.2 m. The discharge of the fluid through…

Q: A first class lever in static equilibrium has a 65 Ib resistance force and 30 lb effort force. The…

Q: 5. For the beam loaded as shown, calculate the internal axial force, shear force, and bending moment…

A: Let's mark the point E as shown in below figure.

Q: The apples fall from the hand of a person in an elevator that moves down quickly, 3 m/s. What is the…

A: Given , Initial velocity ,u= 3 m/sec Final velocity , v= 0 height, h= 2m

Q: The area of the upper face of a rectangular block is .5mx.5m The lower face is fixed. The height of…

Q: PROBLEMS Figure 1. In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is…

A: Draw FBD

Q: So mm 100 mm. Q. locate the Centroid for the folloing areas:

Q: Solar renewable energy plant has 32 solar panel with 48 KW each. What is the solar KW rated output?…

A: Number of solar panels, n= 32 Power output produced by each panel, P= 48 kW To find: Solar kW…

Q: (+) А 12 mm В с 750 N-m 125 mm 25 mm 200 mm D 300 mm

Q: 1. Knowing that at the instant shown the velocity of collar A is 900 mm/s to the left, determine (a)…

A: Given:- Velocity of collar A = -(900 mm/s) I To Find:- Angular velocity of rod ADB Velocity of…

Q: The net work produced by a Gas Turbine Power plant is 85 BTU. What is the efficiency of the said…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

The heat capacity of a liquid is 250 J/K, if its mass is 50 kg the specific heat capacity of the liquid would be

1250 J kg/ K C°
50 J kg/ K C°
125 J kg/ K C°
5 J kg/ K C°

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The heat transfer coefficient between a surface and a liquid is 57 W/(m2K). How many watts per square meter will be transferred in this system if the temperature difference is 10C?
What are the important modes of heat transfer for a person sitting quietly in a room? What if the person is sitting near a roaring fireplace?
2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is
Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
A plane wall, 7.5 cm thick, generates heat internally at the rate of 105 W/m3. One side of the wall is insulated, and the other side is exposed to an environment at 90C. The convection heat transfer coefficient between the wall and the environment is 500 W/m2 K. If the thermal conductivity of the wall is 12 W/m K, calculate the maximum temperature in the wall.
A pipe carrying superheated steam in a basement at 10C has a surface temperature of 150C. Heat loss from the pipe occurs by radiation (=0.6) and natural convection (hc=25W/m2K). Determine the percentage of the total heat loss by these two mechanisms.
The rate of heat flow per unit length q/L through a hollow cylinder of inside radius ri and outside radius ro is q/L=(AkT)/(rori) where A=2/(rori)/ln(ro/ri). Determine the percent error in the rate of heat flow if the arithmetic mean area (ro+ri) is used instead of the logarithmic mean area A for ratios of outside-to-inside diameters (Do/Dj) of 1.5, 2.0, and 3.0. Plot the results.
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
During summer season a room measuring 10 x 13 x 6 m3 is cooled electrically from initial temperature- 28°C to 2°C. The air pressure inside the room is the same as that of surroundings and is equal to 72 cm of Hg. The pressure remains constant during the cooling process. The cooling capacity of furniture and wall is 35 kJ/K. The Cp of air is 1.005 kJ/kgK.Calculate the amount of electric energy needed for cooling the room. How much air comes through gaps and windows during cooling period?
The heat capacity of a liquid is 250 J/K, if its mass is 50 kg the specific heat capacity of the liquid would be 1250 J kg/ K C° 50 J kg/ K C° 125 J kg/ K C° 5 J kg/ K C° No answer
3. A classroom that normally contains 40 people is to be air-conditioned with window air-conditioning units of 5-kW cooling capacity. A person at rest may be assumed to dissipate heat at a rate of about 360 kJ/h. There are 10 light bulbs in the room, each with a rating of 100 W. The rate of heat transfer to the classroom through the walls and the windows is estimated to be 15,000 kJ/h. If the room air is to be maintained at a constant temperature of 210C, determine the number of window air-conditioning units required. draw a figure also, and explain each step by step solution.
THERMODYNAMICS 1. Calculate the amount of energy required in BTU to heat the air in a house 30 by 50 by 40 ft from 10 to 70°F at constant pressure. 2. Brine enters a cooler at the rate of 50 m3/hr at 15°C and leaves at 1°C. Specific heat and specific gravity of brine are 1.07 kJ/kg–K and 1.1 respectively. Calculate the heat transferred in kW. 3. How many BTU/min is required to produce 10 metric tons of ice per day at -10°C from raw water at 22°C? The latent heat of fusion of ice is 335 kJ/kg.