the heat transfer (Q12) in :(kJ) is Below 200 O Between 200 and 400 O Between 400 and 600 O Between 600 and 800 O Above 800 O A piston-cylinder device contains water of quality x-0.7 and pressure 200 kPa with an initial volume of 100 Liter. The system is now heated in isobaric process to a final temperature of 200°C. Piston-cylinder device water, x₁ = 0.7 P₁=PL = 200 kPa Q₁V₁= 100 Liter TΣ - 200°C℃

the heat transfer (Q12) in :(kJ) is Below 200 O Between 200 and 400 O Between 400 and 600 O Between 600 and 800 O Above 800 O A piston-cylinder device contains water of quality x-0.7 and pressure 200 kPa with an initial volume of 100 Liter. The system is now heated in isobaric process to a final temperature of 200°C. Piston-cylinder device water, x₁ = 0.7 P₁=PL = 200 kPa Q₁V₁= 100 Liter TΣ - 200°C℃

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.12P

See similar textbooks

Similar questions

What is the new temperature (in K) of a closed gas system when it's volume is compressed from 5.6 L to 2.3 L and initial temperature was 455ﾟ K
Please answer in 1hr pls do it fast.., A rigid tank with a volume of 0.2 m3 contains saturated liquid water at 120 oC initially. Then 80 kg of of saturated liquid water is slowly drained from the tank, by using a drain valve at the bottom of the tank. Temperature of the water in the tank does not change due to heat interaction with a thermal reservoir at 180 oC. Determine, (a) the final mass of water in the tank, (b) the heat interaction with the thermal reservoir
Water is to be heated from 15°C to 65°C as it flows through a 3-cm-internaldiameter 5-m-long tube . The tube is equipped with an electric resistance heater that provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat generated in the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 10 L/min, determine the power rating of the resistance heater. Also, estimate the inner surface temperature of the tube at the exit.
2. A large sheet of glass 2” thick is initially at 300oF throughout. It is plunged into a stream of running water having a temperature of 60oF. How long will it take to cool the glass to an average temperature of 100oF. For glass k = 0.40BTU/ft-hroF, ρ = 155 lb/ft3 and Cp = 0.20 BTU/lboF.
A long roll of 2-m-wide and 0.5-cm-thick 1-Mn manganesesteel plate (ρ = 7854 kg/m3 and cp = 0.434 kJ/kg·°C)coming off a furnace at 820°C is to be quenched in an oil bathat 45°C to a temperature of 51.1°C. If the metal sheet is movingat a steady velocity of 10 m/min, determine the requiredrate of heat removal from the oil to keep its temperature constantat 45°C.
1. Moist air enters a refrigeration coil at 89 F dry-bulb temperature and 65 F thermodynamic wet bulb temperature at a rate of 14oo cu ft per min. The surface temperature of the coil is 55 F . If 3.5 tons of refrigeration are available, find the dry bulb and wet bulb temperatures of the air leaving the coil. Assume sea level pressure.
Answer with a clean and neat solution In a piston cylinder system, the gas an initial pressure of 100 kPa and expands from 1.5 m3 to 7.5 m3 with an increase in internal energy amounting to [50 + (162/20)] kJ. Calculate the heat gain or loss in the system given the pressure volume relation as P2V is constant, where P is in kPa and V is in m3.
A 4-m × 5-m × 6-m room is to be heated by an electric resistance heater placed in a short duct in the room. Initially, the room is at 15°C, and the local atmospheric pressure is 98 kPa. The room is losing heat steadily to the outside at a rate of 150 kJ/min. A 200-W fan circulates the air steadily through the duct and the electric heater at an average mass flow rate of 40 kg/min. The duct can be assumed to be adiabatic, and there is no air leaking in or out of the room. If it takes 25 min for the room air to reach an average temperature of 25°C, find the temperature rise that the air experiences each time it passes through the heater.
A 4-m × 5-m × 6-m room is to be heated by an electric resistance heater placed in a short duct in the room. Initially, the room is at 15°C, and the local atmospheric pressure is 98 kPa. The room is losing heat steadily to the outside at a rate of 150 kJ/min. A 200-W fan circulates the air steadily through the duct and the electric heater at an average mass flow rate of 40 kg/min. The duct can be assumed to be adiabatic, and there is no air leaking in or out of the room. If it takes 25 min for the room air to reach an average temperature of 25°C, find the power rating of the electric heater.
A rigid tank contains 2.2 lbm of R-134a, initially at 70 psia and 160F. The fluid is then allowed to cool to a final temperature of 40oF. Evaluate the pressure, quality and internal energy of the fluid in its final state.
An air compressor is designed to compress air (assumed to 100 kPa, 20 ° C at a pressure of 1 MPa). Heat losses to the environment are considered in advance to be about 10% of the input power to the compressor. The air enters at 50 m / s where the inlet area is 90cm2 and leaves 120m / s through an area of 5cm2. Determine: a) The air temperature at the outlet and the input power to the compressor. b) Heat coming out of the compressor 10% of the power
Is the work done by the system positive, negative, or zero during an adiabaticprocess where the final temperature is higher than the initial temperatureCan pdV work be done on the system during an isobaric process? What aboutduring an isochoric process?Compare and contrast the concepts of work and heat. What is the difference?