The height of the g point is 0.5m, the distance of the rear wheel to theg point is 1.75m, the distance of the front wheel to the g point is 1.8 m, and the car with a mass of 2100kg brakes suddenly while moving at 24v speed. l-Find the friction coefficient between the wheel and the road? 2-Find the way the vehicle takes until it stops?

The height of the g point is 0.5m, the distance of the rear wheel to theg point is 1.75m, the distance of the front wheel to the g point is 1.8 m, and the car with a mass of 2100kg brakes suddenly while moving at 24v speed. l-Find the friction coefficient between the wheel and the road? 2-Find the way the vehicle takes until it stops?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.59P: How many turns of rope around the capstan are needed for the 40-lb force to resist the 8000-lb pull...

See similar textbooks

Similar questions

The force P applied to the brake handle enables the band brake to reduce the angular speed of a rotating drum. If the tensile strength of the band is 3800 lb, find the maximum safe value of P and the corresponding braking torque acting on the drum. Assume that the drum is rotating clockwise.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
The contact surface between the 36-lb block and 20-lb homogenous cylinder is frictionless. Can the system be in static equilibrium 0n the rough inclined plane?
Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
A uniform plank is supported by a fixed support at A and a drum at B that rotates clockwise. The coefficients of static and kinetic friction for the two points of contact are as shown. Determine whether the plank moves from the position shown if (a) the plank is placed in position before the drum is set in motion; and (b) the plank is first placed on the support at A and then lowered onto the drum, which is already rotating.
The normal pressure acting on the disk of the sander is given by p=(4/3)+(r2/6), where p is the pressure in pounds per square inch (psi) and r represents the radial distance in inches. Determine the torque C required to operate the sander at constant speed if the kinetic coefficient of friction for the surface being sanded is 0.86.
The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of the screw are threaded in opposite directions (right- and left-handed threads). The coefficient of static friction between the threads is 0.08. Calculate the torque C0 that must be applied to the screw in order to start the 1200-1b load moving (a) upward; and (b) downward.
Find the smallest distance d for which the hook will remain at rest when acted on by the force P. Neglect the weight of the hook, and assume that the vertical wall is frictionless.
Calculate the force P that is required to hold the 120-lb roller at rest on the rough incline.