(+)The hollow shaft used inthe system has the followingconditions:ВEOuter Ø: 110 mm ØAllowable Shearing Stress:85 MPa18 KN•MDetermine the thickness (mm)of the shaft. Round to theF35 kN-mnearest whole number for thethickness and use 2 decimalplaces for other solved values.Provide88 kN matorque diagram,strictly follow instructed signconvention, and start from leftto right.35 kN-m

Answered: Image /qna-images/answer/a6d9627d-b43c-4d21-9bc3-279321f80b19.jpg

(+) The hollow shaft used in the system has the following conditions: В Outer Ø: 110 mm Ø Allowable Shearing Stress: 85 MPa 18 KN•M Determine the thickness (mm) of the shaft. Round to the nearest whole number for the 35 kN m thickness and use 2 decimal places for other solved values. Provide 88 kN m a torque diagram, strictly follow instructed sign convention, and start from left to right. 35 kN·m

(+) The hollow shaft used in the system has the following conditions: В Outer Ø: 110 mm Ø Allowable Shearing Stress: 85 MPa 18 KN•M Determine the thickness (mm) of the shaft. Round to the nearest whole number for the 35 kN m thickness and use 2 decimal places for other solved values. Provide 88 kN m a torque diagram, strictly follow instructed sign convention, and start from left to right. 35 kN·m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. Solve dy/dx - cos x = cos x cot^2y show your solution a. 2y + sin 2y = -4 sinx + c b. 2y - sin 2y = -4 sinx + c c. 2y - sin 2y = 4 sin x + c d. none of the above
Use the siopsdeflction method, dra . axal fors, shear fore, and bending ot dingrams fo the e shown i the fgus. e fre has pi uppors t A e D and constat modlus of lastiiy £). The moments of fneria ) for sach mermbr indicted i the fgure. 1510 1510 | 12 k/m
The copper pipe shown in the figure has an outside diameter of 3.375 in. and a wall thickness of 0.386 in. The pipe is subjected to a uniformly distributed torque oft= 71 Ib-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c= 9.25 ft, calculate
Let W0=3.1 kip/ft and L=20ft
Answer only A and B. note: a = 4.5 m b = 33.0 kN/m c = 13 kN
find the length of DE & bearing of BC.
Neslyn used a 30m steel tape used to measure a certain distance. It was later found that the tape is 0.05m too short. The tape has a cross sectional area of 4.6mm2 and weight of 0.3512N/m. It was standardized at a temperature of 25°C and a pull of 55N. During the measurement, the tape was held horizontal and supported at midspan with a constant tension of 434.9N. The temperature at the time of measurement is 31.1°C. If the measured distance is 344.89m, determine the corrected distance (m).
A 50-m steel tape weighing 0.035kg/m isconstantly supported at mid-length and its endpoints, and is used to measure a line AB with asteady pull of 6.5kg. If the measured length ofAB is 1200.00m, determine the following:a. Correction due to sag between supports andfor the whole tape lengthb. Total sag correction for the whole lengthmeasuredc. Correct length of line AB
Steel Design Given: S = 2m L = 10m Superimposed dead load = 5 kPa Live load = 3.6 kPa Properties of Beam BFA section = W 460 x 97 kg/mArea (A) = 12320 mm^2Depth (d) = 465 mmFlange Width (bf) = 193 mmFlange Thickness (tf) = 19mmWeb Thickness (tw) = 11 mm Moment of InertiaIx = 445 x 10^6 mm^4Iy = 23 x 10^6 mm^4Yield Strength, Fy = 248 MPar (radius of gyration of a section compromising the compression flange plus 1/3 of the compression web area of compression flange = 50 mm. Consider bending about the x-axis. 1. The compression flanges are laterally supported only at midspan. With this condition, what is the permissible flexural stress if Cb = 1.0?
A)Draw the M, N, T diagrams of the system. B)Calculate the M values at 25% intervals under distributed loads.
Help, FEM: Given a differential eqn : D2 +3xD-6y =0. Find y(0.2) by Galeskin method.
determine the reactions and moments using slope deflection method referece solution: https://www.bartleby.com/solution-answer/chapter-15-problem-11p-structural-analysis-6th-edition/9781337630931/bb8a9823-94ca-11e9-8385-02ee952b546e will upvote