The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the position shown. Member BD is 5/8 in. thick and is connected to the vertical rod by a 3/8-in.-diameter bolt. Determine (a) the average shearing stress in the bolt, (b) the bearing stress at C in member BD. draw free-body diagram

Q: TWO IDENTICAL LINKAGE-AND-HYDRAULIC-CYLINDER SYSTEMS CONTROL THE POSITION OF THE FORKS OF A…

A:

Q: A torque of magnitude T = 12 kN-m is applied to the end of a tank containing compressed air under a…

A: GivenT=12kN.mP=8MPat=12mmI.D=Di=180mmri=90mm=0.09mro=90+12=102 mm=0.102mSolutionPolar moment of…

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A:

Q: A flanged bolt coupling consists of eight steel 20-mm bolts spaced evenly around a bolt circle of…

A:

Q: In the structure shown, an 8-mm-diameter pin is used at A, and two pins are used at B and D. Knowing…

A: Given data: pin A diameter = dA = 8 mm Ultimate shearing stress  at pin A = 100 MPa = 100 n/mm2

Q: A load P is applied to a steel rod with head dimensions D = 49 mm, and h = 8.7 mm supported by an…

A:

Q: A shaft is made from two segments: AB is pure steel and BCD is pure brass (note: not core-shell).…

A: Let us consider three parts AB, BC and CD . The torque of AB portion is TAB=800Nm , torque on BC…

Q: The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and…

A:

Q: A 5/8-in.-diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For…

A: Given,  Diameter of shaft = 5/8 in = 0.625 in  a)Maximum Average stress in wood Area = 1 X (4-0.625)…

Q: The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the…

A: The length of AB is written as, Free body diagram of the member BD with reaction and force…

Q: Specifications: Shafts AB, BC, CD are solid material. Determine: a) The shaft section in which the…

A: Given data: The diameter of the shaft AB is dAB=0.6 in. The diameter of the shaft BC is dBC=0.75…

Q: Question (a) For the 60-mm-diameter solid cylinder and loading shown, determine the maximum shearing…

A:

Q: the pins at A and B if the allowable normal stress for member BC is Oallow = 35 ksi and the…

A: Handwritten.jpg

Q: 9 The uniform plate ABCD, weighing 1200-lb, can freely rotate about the hinge AB. The cables DE and…

A:

Q: The steel jacket CD has been attached to the 40-mm-diameter steel shaft AE by means of rigid flanges…

A: Given Data: The outer diameter of the jacket is D = 80 mm. The thickness of the jacket is t = 4 mm.…

Q: 1. The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

A:

Q: The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in the…

A: GivenThickness of member BD=15mmP=2knθ=75° FBD of BCD

Q: cylinders shown.  a) For the 3-in. diameter solid cylinder and loading shown, determine the maximum…

A:

Q: 8. The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in…

A: Given: The diameter of bolt at C, d = 3/8 in The thickness pf BD, t = 5/8 in

Q: 4.2 (B). Determine from first principles the hoop stress at the inside and outside radius of a thin…

A: Given Data: The outer diameter of the thin disc is Do = 300 mm. The inner diameter of the thin disc…

Q: The bell crank shown is in equilibrium determine the required diameter of the connecting rod AB if…

A: Force acting along the horizontal direction is, Dx=110cos60+P=110cos60+70=125 kN Forces acting in…

Q: A flanged bolt coupling consists of ten 15-mm diameter bolts spaced evenly around a bolt circle 350…

A:

Q: For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear…

A: The free-body diagram of the membr ECD is shown below.   Equilibrium of forces on point, E ∑Fx = 0…

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 84 MPa, and sleeve CD…

A: Given Data  Allowable shear stress, T=50 MPa Ans(A)  Consider CD…

Q: For the riveted connection shown, the allowable shearing stress in the 25mm rivets is 140 MPa.…

A:

Q: Problem 2: A 4 by 4 – in. w0od – post BC is connected to a 1 – in. diameter steel eye – bar AB to…

A: FAy=513FA ∑Mc=0 7000*5=FA*513*7 FA=13000 lbs      (T) σAB=FAA=13000*4π*12=16552.1 psi ∑Fy=0…

Q: determine the bolt diameter required in mm. (b) If the shaft is made of the same material as the…

A:

Q: The ship at A has just started to drill for oil on the ocean floor at a depth of 5000 ft. Knowing…

A:

Q: A 240-kip load P is applied to the granite block shown. Determine the resulting maximum value of (a)…

A: a) Maximum normal stress can be determined as

Q: The solid rod AB has a diameter dAB = 60 mm. The pipe CD has an outer diameter of 90 mm and a wall…

A:

Q: Two solid brass rods AB and CD are brazed to a brass sleeve EF. Determine the ratio d2/d1 for which…

A: Given data Radius of soild brass r1 = d12Radius of brass sleeve EF ro = d22Inner radius of brass…

Q: The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

A: The value of the direct shear force can be neglected. The value of the torque on the shaft can be…

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: Given data as per question Shear stress in solid spindle =12 ksiShearing stress of sleeve=5.8…

Q: 8. The hydraulic cylinder CF, which partially controls the position of rod DE, has been locked in…

A: Free body diagram for the given cylinder,

Q: a) For the 3-in.-diameter solid cylinder and loading shown, deter-mine the maximum shearing stress.…

A: (a) Calculate the maximum shearing stress                          τ=TcJ=40×32π21.54=7.53 ksi

Q: Determine the largest load P that can be applied at A when 0 = 50° , knowing that the allowable…

A: Pin diameter, dpin= 10 mm Thickness of the member AB, t= 16 mm Thickness of the bracket at B. tb= 12…

Q: 3. The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve…

A: a) Calculation for sleeve CD: (C2)Radius=12*3 inch=1.5 inch C1=C2-t=1.5-0.25=1.25 inch

Q: The frame system will be used to support the 1.8m diameter cylindrical tank by a hanger system AC…

A: we are tasked to figure out the reactions at A and C  , and from there figure out the stresses at…

Q: Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20-mm…

A:

Q: The design of a machine element calls for a 40-mm-outer diameter shaft to transmit 45 kW. (a) If the…

A:

Q: For the frame shown, a 4998-N load is acting on member ABD at D. If the allowable material shear…

A:

Q: The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow…

A:

Q: The frame system will be used to support the 1.8m diameter cylindrical tank by a hanger system AC…

A: Given: W = 15 kN D = 1.8 m so, R = 0.9 m FOS = 4 σut = 300 MPa

Q: 4. (Problem 8.43 from the text book) The steel pipe AB has a 72-mm outer diameter and a 5- mm wall…

A: Answer: (a) The principal stresses at point K : ◆ Major Principal Stress: 78.7526 MPa (Tensile). ◆…

Q: 1. The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

A:

Q: 03-A- In the gear-and-shaft system shown, the shaft diameters are dAB- nm. Knowing that G=77 GPa.…

A:

Q: Determine the diameter of the largest circular hole that can be punched into a sheet of polystyrene…

A: Plate will failed due to shear stressShearing Area=π d t

Q: The composite shaft shown is to be twisted by applying a torque T at end A. Knowing that the modulus…

A: Given data: Composite shaft is made of Steel core and Aluminum Jacket. Diameter of steel core,…

Q: 4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A…

A: