: The information in analog signal voltage waveform is to be transmitted over a PCM system with maximum quantization error (±0.1%). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volis. egsx-x9 889 s a) Determine the maximum sampling rate required. b) Determine the number of bits in each PCM word. - Amina A i

: The information in analog signal voltage waveform is to be transmitted over a PCM system with maximum quantization error (±0.1%). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volis. egsx-x9 889 s a) Determine the maximum sampling rate required. b) Determine the number of bits in each PCM word. - Amina A i

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

For a CD audio system, the analog signal is digitized such that the signal to quantization ratio is maintained at least 96dB. The sampling is performed at 44100Hz. a) What is the minimum number of quantization levels required to attain the given signal to quantization noise ratio?b) How many bits per sample are required when levels are identified in part a)?c) Identify the data rate in bits/s for the system.
Question 3 3. A communication system transmits an analog waveform via a Yagi antenna of length 3m. The analog wave form is carrier modulated and transmitted over a Maray PAM system, where the number of pulse level is M = 64. The quantization distortion must not exceed ± 2% of the peak-to-peak analog signal. i What is the maximum number of bits per sample that should be used in this PCM? ii. What is the minimum sampling rate? iii. Determine the maximum frequency iv. What’s the resulting bit transmission rate? v. Compute the sampling time
q15) This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. If the quantization error must not exceed 2% of the peak-to-peak analog signal. Then the minimum number of bits per sample is equal to a)none of the mentioned b)4 c)6 d)5
For a FM system, the maximum freq deviation is 75 kHz and the maximum freq of the info. signal is 10 kHz. What will be the total bandwidth of the FM system? What will be the modulation index?
1. a. Create the gray code representation of the following binary numbers.i) 01011 ii) 10110 iii) 01101 iv) 11001 b. If a computer’s system clock is 2.7 GHz, calculate the period of the system clock. c. What is the minimum sampling rate needed in order to successfully capture frequencies up to 60MHz in an analog signal? d. Represent the number 1.00011011101 x 2-23in IEEE Standard 754 single precision floating point binary.
Q24)This multiple choice question from DIGITAL COMMUNICATIONS course.just write for me the final answer. The choice of the number of bits per PCM word depends on the a. SNR b. Bandwidth c. None of the mentioned d. SNR and bandwidth
What is meant as baud rate? I don't understand explain in bit details and what's the difference between baud rate and bit rate?
Derive an expression of Probability of error of Binary Frequency Shift Keying.( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
determine (a) the peak frequency deviation (b) minimum bandwidth, and (c) baud for a binary FSK signal with a mark frequency of 275 mHz, a space frequency of 395 kHz, and an input bit rate of 6 kbps
1. What are the control methods for electromechanical systems. What arethe advantages of each method? 2. What are the design steps for a microcontroller basedelectromechanical system? 3. Given that sampling frequency (fs) is equal to 250Hz and Nyquistfrequency (fN) is equal to two times of the alias frequency, find the aliasfrequency. 4. You need to design a quantizer for a sensor which measures voltagevalues between 40 V and 200 V. If your resolution is 4 (n value) findthe number of output states (N) and quantization step (Q). 5. Design a capacitive transducer to be able to measure the displacementof a rotating element in a machine. Sketch the diagram and specifywhich parameters will let you measure the displacement.
An a differential pulse code modulated system, the transmitted bits per sample is 7. How many levels are present in the quantizer?
For a PCM system with the following parameters, Parameters: (i) Maximum analog input frequency = 5 kHz; (ii) Maximum decoded voltage at the receiver = ±5.01 V; (iii) Minimum dynamic range = 54 dB. (Use 2 decimal places) a) What is the coding efficiency in % b) What is the resolution in V? c) Determine the maximum quantization error in V. d) Determine the minimum sampling rate in KHz e)Determine minimum number of bits use for the PCM code excluding sign bit.